Driver Side Door Entry Lock and Unlock Functions Do Not Operate
THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function): Driver Side Door Entry Lock and Unlock Functions do not Operate
- Driver Side Door Entry Lock and Unlock Functions do not Operate
DESCRIPTION
When the driver side door entry lock and unlock functions do not operate, one of the following may be malfunctioning: 1) power door lock system, 2) driver side door electrical key oscillator, or 3) certification ECU (smart key ECU assembly).
WIRING DIAGRAM
INSPECTION PROCEDURE
PROCEDURE
1. CHECK POWER DOOR LOCK OPERATION
(a) When the master switch assembly door control switch is operated, check that the locked doors unlock.
OK:
Door locks operate normally.
NG -- GO TO POWER DOOR LOCK CONTROL SYSTEM Operation Check
OK -- Continue to next step.
2. READ VALUE USING TECHSTREAM
(a) Using the Techstream, read the Data List.
Smart Key
Result
B -- REPLACE FRONT DOOR OUTSIDE HANDLE Removal
A -- Continue to next step.
3. CHECK WAVE ENVIRONMENT
(a) Bring the electrical key transmitter near the driver side door outside handle, and perform a driver side door entry lock and unlock operation check.
NOTICE:
If the key is brought within 0.2 m (0.656 ft.) of the door handle, communication is not possible.
HINT
* When the electrical key transmitter is brought near the driver side door outside handle, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
* If the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
Result
B -- AFFECTED BY WAVE INTERFERENCE
A -- Continue to next step.
4. PERFORM KEY DIAGNOSTIC MODE INSPECTION
(a) Diagnostic mode inspection (driver side door electrical key oscillator).
(1) Connect the Techstream to the DLC3.
(2) Turn the engine switch on (IG).
(3) Turn the Techstream on.
(4) Enter the following menus: Body Electrical / Smart Key / Smart Communication Check / Overhead + Driver Side.
(5) When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds.
HINT
If the buzzer sounds, it can be determined that the driver seat outside transmitter is operating normally.
OK:
Wireless door lock buzzer sounds.
NG -- CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR ELECTRICAL KEY OSCILLATOR)
OK -- REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) Removal
5. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] - DOOR ELECTRICAL KEY OSCILLATOR)
(a) Disconnect the E29 ECU connector.
(b) Disconnect the z24 oscillator connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
6. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE)
(a) Disconnect the z23 handle connector.
(b) Disconnect the z24 oscillator connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
7. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - BATTERY AND BODY GROUND)
(a) Disconnect the z24 oscillator connector.
(b) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
8. REPLACE DOOR ELECTRICAL KEY OSCILLATOR
(a) Replace the door electrical key oscillator Disassembly.
NEXT -- Continue to next step.
9. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
(a) Check that the entry function operates normally.
OK:
Operates normally.
NG -- REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) Removal
OK -- END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)