Reassembly
SEAT: FRONT SEAT ASSEMBLY (for Manual Seat): REASSEMBLY
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
HINT
* Use the same procedure for the RH and LH sides.
* The procedure listed below is for the LH side.
1. INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY Installation
2. INSTALL NO. 2 SEAT WIRE (for Driver Side)
(a) Attach the 2 clamps to install the seat wire.
(b) Connect the connector.
3. INSTALL SEPARATE TYPE FRONT SEATBACK PAD
(a) Install the seatback pad.
4. INSTALL SEPARATE TYPE FRONT SEATBACK COVER
(a) Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
Text in Illustration
NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, avoid wrinkling the cover.
(b) Attach the 4 claws to install the 2 headrest supports.
(c) Connect the seatback cover bracket to the seatback pad.
(d) Install the seatback cover bracket to the seat frame with the nut.
Torque : 5.5 Nm (56 kgf-cm, 49 in-lbf)
NOTICE:
After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.
(e) Close the 2 fasteners, and then close the seatback cover.
(f) Using hog ring pliers, install new 3 hog rings.
Text in Illustration
5. INSTALL RECLINING ADJUSTER INSIDE COVER LH
(a) Move the cover in the direction of the arrow to install the cover.
(b) Attach the guide.
6. INSTALL RECLINING ADJUSTER INSIDE COVER RH
HINT
Use the same procedure described for the LH side.
7. INSTALL FRONT SEAT WIRE LH
(a) Install the seat wire.
8. INSTALL OCCUPANT CLASSIFICATION ECU (for Front Passenger Side)
(a) Attach the claw to install the ECU.
(b) Connect the 2 connectors.
9. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH
(a) Move the protector in the direction of the arrow to attach the hook and install the protector.
(b) Install the screw.
10. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH
HINT
Use the same procedure described for the LH side.
11. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH
(a) Attach the hook and clip to install the cushion shield.
(b) Install the screw.
12. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH
(a) Attach the hook and clip to install the cushion shield.
(b) Install the screw.
13. INSTALL RECLINING ADJUSTER INSIDE COVER LH
(a) Attach the claw and guide to install the cover.
14. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
(a) Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
Text in Illustration
NOTICE:
* Be careful not to damage the cover.
* When installing the hog rings, avoid wrinkling the cover.
15. INSTALL SEAT CUSHION COVER WITH PAD
(a) Install the seat cushion cover with pad.
(b) Attach the hooks.
16. INSTALL FRONT SEAT LEG COVER LH
(a) Move the cover in the direction of the arrow to install the cover.
(b) Attach the 2 claws.
17. INSTALL SEAT ADJUSTER COVER CAP
(a) Install the 2 caps.
18. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY
(a) Install the seatback assembly with the 4 bolts.
Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)
(b) Connect the airbag wire harness.
(c) Attach the fastening tape to close the cover.
(d) Attach the 3 airbag wire harness clamps.
(e) Attach the claw and disconnect the airbag connector.
(f) Install the 2 clips.
(g) for Driver Side:
Attach the clamp to connect the No. 2 seat wire.
(h) Install the rubber band to the seat cushion spring.
19. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH Installation
20. INSTALL FRONT SEAT INNER CUSHION SHIELD LH
(a) Attach the 3 claws to install the cushion shield.
21. INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)
(a) Attach the 4 claws to install the cushion shield.
22. INSTALL LUMBAR SWITCH ASSEMBLY (for Driver Side) Installation
23. INSTALL FRONT SEAT CUSHION SHIELD LH
(a) for Driver Side:
Attach the 5 wire harness clamps and connect the 2 connectors.
(b) Attach the 4 claws and clip to install the cushion shield.
(c) Install the screw.
24. INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)
(a) Install the handle with the screw.
25. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH
(a) Attach the claw to install the handle.