Intake Air Temperature Sensor, Checking
Intake Air Temperature Sensor, Checking
• The Mass Air Flow sensor and the Intake Air Temperature sensor are combined as a unit and are serviced as an assembly.
• Use only gold-plated terminals when servicing terminals in the electrical harness connector of the MAF / IAT sensor (G70 / G42).
Special tools, testers and auxiliary items required
• multimeter.
• Wiring diagram.
Test procedure
- Perform a preliminary check to verify the customers complaint. Refer to => [ Preliminary Check ] Preliminary Check
Start diagnosis
- Connect the scan tool.
- Engine must be at room temperature.
- Switch the ignition on.
- Using the scan tool, check the intake air temperature:
If the specified values are obtained:
- Fault is intermittant. Check for proper connection, damaged wiring or loose terminals.
If the specified value is not obtained:
- Continue the test according to the following table:
Checking Component and wiring
- Disconnect the MAF / IAT sensor (G70 / G42) electrical harness connector - arrow -.
- Using a multimeter, connect the positive lead to the MAF / IAT sensor (G70 / G42) harness connector terminal 1 and the negative lead to an engine ground.
Specified value: 4.30 V to 4.90 V
If the specification was not obtained:
- Check the wiring for an open, high resistance or short to ground.
- Check the electrical harness connector for damage, corrosion, loose or broken terminals.
- If necessary, repair the faulty wiring or connection.
If voltage was not present and no malfunction is detected in the signal circuit:
- Replace the Motronic Engine Control Module (ECM) (J623). Refer to => [ Motronic Engine Control Module, Replacing ] Motronic Engine Control Module, Replacing.
- If voltage was in specification:
- Using a multimeter, connect the positive lead to Battery + and the negative lead to the MAF / IAT sensor (G70 / G42) harness connector terminal 3.
Specified value: Battery voltage.
If the specification was not obtained:
- Check the ground circuit for an open or high resistance.
- Check the electrical harness connector for damage, corrosion, loose or broken terminals.
- If necessary, repair the faulty wire or connection.
If voltage was in specification:
- Replace the MAF / IAT sensor (G70 / G42)
°Testing if display is - 40 C :
- Disconnect the MAF / IAT sensor (G70 / G42) electrical harness connector - arrow -.
- Using a jumper wire, connect the MAF / IAT sensor (G70 / G42) electrical harness connector terminals 4 to 5.
- Check the value indicated on the scan tool display.
If indication jumps to approx. 140 °C:
- Switch ignition off.
- Replace the MAF / IAT sensor (G70 / G42)
If indication remains at approx. -40 °C or -46 °C:
Checking wiring
If the manufacturers test box is being used, perform the following step.
- Install the test box.
If the manufacturers test box is not being used, perform the following step.
- Remove the Motronic Engine Control Module (ECM) (J623). Refer to => [ Motronic Engine Control Module, Replacing ] Motronic Engine Control Module, Replacing.
- Using a multimeter, check the MAF / IAT sensor (G70 / G42) electrical harness connector terminal 1 to the Motronic Engine Control Module (ECM) (J623) electrical harness connector T121 terminal 26 for an open circuit or a short to voltage, refer to the wiring diagram.
- Using a multimeter, check the MAF / IAT sensor (G70 / G42) electrical harness connector terminal 3 to the Motronic Engine Control Module (ECM) (J623) electrical harness connector T121 terminal 27 for an open, high resistance or a short to voltage, refer to the wiring diagram.
Specified resistance: 1.5 ohms Max.
If the specification was not obtained:
- Check the wiring for an open, high resistance or short circuit to Battery (+).
- Check the electrical harness connector for damage, corrosion, loose or broken terminals.
- If necessary, repair the faulty wiring connection.
If no malfunction is detected in the wiring:
- Replace the Motronic Engine Control Module (ECM) (J623). Refer to => [ Motronic Engine Control Module, Replacing ] Motronic Engine Control Module, Replacing.
°Testing if display near 140 C:
- Disconnect the MAF / IAT sensor (G70 / G42) electrical harness connector - arrow -.
- Using the scan tool, check the intake air temperature:
If indication jumps to approx. -40 °C to -46 °C:
- Switch ignition off.
- Replace the MAF / IAT sensor (G70 / G42)
If the indication remains at approx. 140 °C:
Checking wiring
- Remove the Motronic Engine Control Module (ECM) (J623). Refer to => [ Motronic Engine Control Module, Replacing ] Motronic Engine Control Module, Replacing.
- Disconnect the T121 connector.
- Using a multimeter, check for continuity between the MAF / IAT sensor (G70 / G42) electrical harness connector terminal 1 to an engine ground, refer to the wiring diagram.
- Using a multimeter, check for continuity between the MAF / IAT sensor (G70 / G42) electrical harness connector terminal 3 to terminal 1, refer to the wiring diagram.
Specified value: OL or no continuity.
If the specification was not obtained:
- Repair the short to ground.
If no malfunction is detected in the wiring:
- Replace the Motronic Engine Control Module (ECM) (J623). Refer to => [ Motronic Engine Control Module, Replacing ] Motronic Engine Control Module, Replacing.
Final procedures
After the repair work, the following work steps must be performed in the following sequence:
1. Check the DTC memory. Refer to => [ Diagnostic Mode 03 - Read DTC Memory ] Diagnostic Mode 03 - Read DTC Memory.
2. If necessary, erase the DTC memory. Refer to => [ Diagnostic Mode 04 - Erase DTC Memory ] Diagnostic Mode 04 - Erase DTC Memory.
3. If the DTC memory was erased, generate readiness code. Refer to => [ Readiness Code ] Readiness Code.