B196F
B196F - Power Liftgate Open Direction Ratchet Primary Switch Performance
For a complete wiring diagram, refer to.
• When Monitored: Whenever the power liftgate is performing a opening operation.
• Set Condition: The liftgate Ajar switch remained open during a power open cycle.
Theory of Operation
The primary ratchet (ajar) switch must remain closed when the liftgate is fully open or between full open and closed positions. The switch will open when the liftgate is fully closed and latched. This switch indicates when the latch is in primary position. It is open when in primary and closed when out of primary.
Test Step 1 - DTC Present
• This DTC will only set during the releasing operation after the 4 second time out. This may make it difficult to reproduce.
• With the scan tool, record and erase DTCs.
• Turn the ignition OFF, wait 10 seconds, then turn the ignition ON.
• Operate the power liftgate several times if possible.
• With the scan tool, read Active DTCs.
Does the scan tool display B196F - Power Liftgate Open Direction Ratchet Primary Switch Performance?
Yes
• Go to Test Step 2
No
• Using the wiring diagram/schematic as a guide, inspect the wiring and connectors for an intermittent condition. Operate the door several times and check for any binding or other obstructions.
• Perform the Body Verification Test. Refer to => Non-DTC Based Diagnostics. Body Interior
Test Step 2 - Binding Liftgate
• Examine the liftgate for proper fit and alignment, loose/hard or torn seals, misaligned latch striker or anything that would cause an obstruction to proper operation.
• Check the liftgate seal. If it is to soft or to hard it will not provide a proper "Pop - Off" when the gate is unlatched.
• Manually operate the liftgate of a known good vehicle and notice the effort needed to open and close.
• Compare the effort needed on the disabled liftgate.
• Especially notice the effort needed to unlatch and close the liftgate.
Does it take more effort to operate the liftgate than it should?
Yes
• Refer to service information for the related symptoms.
• Perform the Body Verification Test. Refer to => Non-DTC Based Diagnostics. Body Interior
No
• Go to Test Step 3
Test Step 3 - Power Liftgate Module
• With the scan tool, monitor the primary ratchet switch.
• Using a screwdriver, click the latch to the second detent while observing the scan tool.
• Unlatch the latch by pressing the handle switch and observe the scan tool for a change of state.
• Repeat this step several times while moving the liftgate in different positions and wiggling the harness to check for an intermittent open or short circuit.
Did the scan tool show the switch state changing correctly every time?
No
• Go to Test Step 4
Yes
• Replace the power liftgate module.
• Perform the Body Verification Test. Refer to => Non-DTC Based Diagnostics. Body Interior
Test Step 4 - Check the Logic Ground Circuit for an Open
• Turn the ignition OFF.
• Turn all light off.
• Disconnect the power liftgate latch harness connector.
• Measure the resistance between ground and the logic ground circuit in the power liftgate latch connector.
• Wiggle the harness while observing the ohmmeter.
Is the resistance less than 9.5 ohms?
Yes
• Go to Test Step 5
No
• Repair the logic ground circuit for an open.
• Perform the Body Verification Test. Refer to => Non-DTC Based Diagnostics. Body Interior
Test Step 5 - Liftgate Ajar Switch Sense Circuit Open
• Disconnect the power liftgate module C2 harness connector.
• Measure the resistance of the liftgate ajar switch sense circuit between the power liftgate C2 harness connector and the power liftgate latch connector.
• Wiggle the harness while observing the ohmmeter.
Is the resistance less than 2.0 ohms?
Yes
• Replace the power liftgate latch.
• Perform the Body Verification Test. Refer to => Non-DTC Based Diagnostics. Body Interior
No
• Repair the liftgate ajar switch sense circuit for an open.
• Perform the Body Verification Test. Refer to => Non-DTC Based Diagnostics. Body Interior