Transmission and Clutch Housings Overview
Transmission and Clutch Housings Overview
1 Transmission Housing
• When replacing: Adjust the input shaft and the differential. Refer to => [ Adjustment Overview ] Adjustment Overview.
2 Needle Bearing
• For the output shaft.
• Removing, refer to => [ Needle Bearing, Removing ] Transmission and Clutch Housings.
• Installing and securing, refer to => [ Needle Bearing, Installing ] Transmission and Clutch Housings.
3 Fluid Fill Plug
• 35 Nm
• The fluid level cannot be checked by removing the oil fill plug.
• If the transmission was disassembled, it must be filled before being installed again.
• Manual transmission capacity (transmission completely disassembled). Refer to Fluid Capacity Tables.
• Manual transmission capacity (transmission partly disassembled). Refer to Fluid Capacity Tables.
4 Outer Race/Tapered Roller Bearing
• For the output shaft.
• Removing and installing, refer to => [ Output Shaft ] Output Shaft.
• When replacing: adjust the output shaft. Refer to => [ Output Shaft, Adjusting ] Output Shaft, Adjusting.
5 Adjusting Shim
• For the output shaft.
• Adjustment overview, refer to => [ Adjustment Overview ] Adjustment Overview.
6 Adjusting Shim
• For the input shaft.
• Adjustment overview, refer to => [ Adjustment Overview ] Adjustment Overview.
7 Outer Race/Tapered Roller Bearing
• For the input shaft.
• Removing and installing, refer to => [ Input Shaft ] Input Shaft.
• When replacing: adjust the input shaft. Refer to => [ Input Shaft, Adjusting ] Input Shaft, Adjusting.
8 Outer Race/Tapered Roller Bearing
• For the input shaft.
• Removing and installing, refer to => [ Input Shaft ] Input Shaft.
• When replacing: adjust the input shaft. Refer to => [ Input Shaft, Adjusting ] Input Shaft, Adjusting.
9 Needle Sleeve
• Removing and installing, refer to => [ Reverse Shaft ] Reverse Shaft.
10 Alignment Sleeve
• Quantity: 2
11 Clutch Housing
• When replacing, refer to => [ Adjustment Overview ] Adjustment Overview.
12 Guide Sleeve
• With a seal for the drive axle and vulcanized O-ring.
• Remove the seal, refer to => [ Removing the Seal from the Guide Sleeve ] Transmission and Clutch Housings.
• Install the seal, refer to => [ Installing the Seal all the Way Into the Guide Sleeve ] Transmission and Clutch Housings.
• Remove the guide sleeve to remove the seal.
• Replace the guide sleeve and O-ring if the O-ring is damaged.
13 Bolt
• 20 Nm
14 Seal and Sleeve (One-Piece)
• For the right flange shaft.
• If the seal is damaged, replace both the seal and sleeve.
• Removing, refer to => [ Removing the Seal and Sleeve ] Transmission and Clutch Housings.
• Installing, refer to => [ Installing the Seal and Sleeve ] Transmission and Clutch Housings.
15 Fluid Drain Plug
• 35 Nm
16 Outer Race/Tapered Roller Bearing
• For the differential.
• Removing and installing, refer to => [ Differential ] Service and Repair.
• When replacing: adjusting the differential, refer to => [ Differential, Adjusting ] Differential, Adjusting.
17 Magnet
• Held in place by the housing joint surface.
18 Oil Catch Tray
• Install the oil catch tray into the transmission housing. Refer to => [ Installing the Oil Catch Tray into the Transmission ] Transmission and Clutch Housings.
19 Outer Race/Tapered Roller Bearing
• For the differential.
• Removing and installing, refer to => [ Differential ] Service and Repair.
• When replacing: adjusting the differential. Refer to => [ Differential, Adjusting ] Differential, Adjusting.
20 Adjusting Shim
• For the differential.
• Adjustment overview, refer to => [ Adjustment Overview ] Adjustment Overview.
21 Seal
• For the left flange shaft.
• Removing and installing, refer to => [ Left Flange Shaft and Seal ] Left Flange Shaft and Seal.