C0267
DTC C0267
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis Strategy Based Diagnosis for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions Diagnostic Procedure Instructions provides an overview of each diagnostic category.
DTC Descriptor
DTC C0267 00
- Low Brake Fluid Indicated
DTC C0267 05
- Low Brake Fluid Indicated High Voltage/Open
Diagnostic Fault Information
Circuit/System Description
The brake fluid level switch monitors the level of the brake fluid in the brake fluid reservoir. When the electronic brake control module sees the brake fluid level switch input closed, the DTC is set.
Conditions for Running the DTC
Ignition ON.
Conditions for Setting the DTC
* Low brake fluid level is detected for 5 s.
* An open is detected on the ground circuit.
* An open, short to ground, or short to voltage is detected on the signal circuit.
Action Taken When the DTC Sets
* The electronic brake control module disables the traction control and stability control for the duration of the ignition cycle.
* The traction control/stability control-active indicator turns ON.
* The brake warning indicator turns ON.
Conditions for Clearing the DTC
The condition for setting the DTC is no longer present.
Reference Information
Schematic Reference
Hydraulic Brake Schematics [1][2]Electrical Diagrams
Connector End View Reference
Component Connector End Views Fuel Pump and Level Sensor Assembly
Description and Operation
Hydraulic Brake System Description and Operation Hydraulic Brake System
Electrical Information Reference
* Circuit Testing Circuit Testing
* Connector Repairs Connector Repairs
* Testing for Intermittent Conditions and Poor Connections Testing for Intermittent Conditions and Poor Connections
* Wiring Repairs Wiring Repairs
Scan Tool Reference
Control Module References Control Module References for scan tool information
Circuit/System Verification
1. Verify that the brake fluid has the proper level. The fluid level should be above minimum level.
• If low
Refer to Brake Fluid Loss Brake Fluid Loss.
• If above minimum level
2. Refer to Circuit/System Testing.
Circuit/System Testing
1. Ignition OFF and all vehicle systems OFF, disconnect the harness connector at the B20 Brake Fluid Level Switch. It may take up to 2 minutes for all vehicle systems to power down.
2. Test for less than 10 ohms between the ground circuit terminal 2 and ground.
• If 10 ohms or greater
1. Ignition OFF.
2. Test for less than 2 ohms in the ground circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, repair the open/high resistance in the ground connection.
• If less than 10 ohms
3. Ignition ON.
4. Verify the scan tool Brake Fluid Level Sensor parameter is OK.
• If the parameter is not OK
1. Ignition OFF, disconnect the harness connector at the K17 Electronic Brake Control Module.
2. Test for infinite resistance between the signal circuit terminal 1 and ground.
• If less than infinite resistance, repair the short to ground on the circuit.
• If infinite resistance, replace the K17 Electronic Brake Control Module.
• If the parameter is OK
5. Install a 3 A fused jumper wire between the signal circuit terminal 1 and ground.
6. Verify the scan tool Brake Fluid Level Sensor parameter is Low.
• If the parameter is not Low
1. Ignition OFF, disconnect the harness connector at the K17 Electronic Brake Control Module, ignition ON.
2. Test for less than 1 V between the signal circuit and ground.
• If 1 V or greater, repair the short to voltage on the circuit.
• If less than 1 V.
3. Test for less than 2 ohms in the signal circuit end to end.
• If 2 ohms or greater, repair the open/high resistance in the circuit.
• If less than 2 ohms, replace the K17 Electronic Brake Control Module.
• If the parameter is Low
7. Test or replace the B20 Brake Fluid Level Switch.
Repair Instructions
Perform the Diagnostic Repair Verification Verification Tests after completing the repair.
* Brake Fluid Level Indicator Switch Replacement (J64) Brake Fluid Level Indicator Switch Replacement (J64)Brake Fluid Level Indicator Switch Replacement (J55) Brake Fluid Level Indicator Switch Replacement (J55)
* Control Module References Control Module References for Electronic Brake Control Module replacement, programming and setup.