Second Seat
SECOND SEAT
SEATBACK : Disassembly and Assembly
DISASSEMBLY
1. Remove the armrest.
1. Pull armrest outer cover (1) lower side forward and remove pawls. Lift armrest outer cover upward to remove.
Triangle: Pawl
2. Remove the armrest mounting nuts and then remove the armrest.
2. Remove the seatback retainers (A), and then open the fasteners
(B).
3. Remove the seatback board and the clips.
1. Slide and align the clips (B) to the holes on the seatback as shown in the figure, and then remove the seatback board
(A).
2. Remove the clips after removing the seatback board.
4. Disconnect the seatback heater unit harness connector (A).
(heater seat model only)
5. Remove the rear seat lever assembly.
1. Remove the rear seat lever assembly fixing screws.
2. Lift rear seat lever assembly and remove seatback control wire.
6. Remove the seatback center finisher.
1. Pull seatback center finisher cover rearward to remove.
Triangle: Pawl
2. Remove the seatback center finisher fixing screws.
3. Remove the seat belt from seatback center finisher.
7. Remove the center seat belt anchor.
1. Remove the seat cushion and seat cushion under cover. Service and Repair.
2. Remove the center seat belt anchor. Removal And Installation.
8. Remove the seatback trim and seatback pad.
1. Remove the headrest holder.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
2. Roll up seatback trim (2) from backward to forward so that seat control lever escutcheon (1) is visible.
3. Remove the seat control lever escutcheon (1).
Triangle: Pawl
4. Remove the seatback trim and seatback pad from the seatback frame.
5. Remove the hog rings, and separate the seatback trim and seatback pad.
9. Remove the seat belt retractor.
10. Remove the seatback frame.
1. Remove the device arm cover.
2. Remove the reclining device inner cover (outside) and reclining device inner cover (inside). Service and Repair.
3. Remove the reclining device outer cover (outside) and reclining device outer cover (inside). Service and Repair.
4. Remove the seatback control wire (A) and seat cushion control wire (B).
5. Remove the reclining inner cover (outside).
6. Remove the mounting bolts and then remove seatback frame.
1. Remove the seatback retainers (A), and then open the fasteners
(B).
2. Remove the seatback board and the clips.
1. Slide and align the clips (B) to the holes on the seatback as shown in the figure, and then remove the seatback board
(A).
2. Remove the clips after removing the seatback board.
3. Disconnect the seatback heater unit harness connector (A).
(heater seat model only)
4. Remove the rear seat lever assembly.
1. Remove the rear seat lever assembly fixing screws.
2. Lift rear seat lever assembly and remove seatback control wire.
5. Remove the seatback trim and seatback pad.
1. Remove the headrest holder.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
2. Roll up seatback trim (2) from backward to forward so that seat control lever escutcheon (1) is visible.
3. Remove the seat control lever escutcheon (1).
Triangle: Pawl
4. Remove the seatback trim and seatback pad from the seatback frame.
5. Remove the hog rings, and separate the seatback trim and seatback pad.
6. Remove the seatback frame.
1. Remove the reclining device outer cover (outside) and reclining device outer cover (inside). Service and Repair.
2. Remove the seatback control wire (A) and seat cushion control wire (B).
3. Remove the reclining inner cover (outside).
4. Remove the mounting bolts and then remove seatback frame.
ASSEMBLY
Assemble in the reverse order of disassembly.
CAUTION:
- Install the hog rings of seat trim in position, and then securely connect the trim or trim cord with the seat frame.
- Adjust the cable when installing the seatback control wire and seat cushion control wire. Adjustments.