Front Parking Aid Camera Wiring Harness - Main Body Section

Front Parking Aid Camera Wiring Harness - Main Body Section

Removal

CAUTION: Make sure that the camera overlay wiring harness is not bent excessively during this procedure. Failure to follow this instruction may result in damage to the harness.
1 Remove the LH B-pillar trim panel. For additional information, refer to B-Pillar Trim Panel B-Pillar Trim Panel
2 Repeat procedure for the other side.




3 Remove the 2 rear bolts from the LH front seat.




4 Release the LH front seat.
- Move the LH front seat fully backwards.
- Remove the 2 front seat front bolts.
5 Remove the RH front seat. For additional information, refer to Front Seat Front Seat




6 With assistance remove the LH front seat.
- Disconnect the 4 electrical connectors.




7
NOTE:
Left-hand shown, right-hand similar.
Remove the front scuff plate trim panel.
- Release the 7 clips.
- Repeat to the other side.




8 Remove the B-pillar floor covering trim panel.
- Remove the 2 clips.
- Repeat to the other side.




9 Remove the parking aid camera module cover.
- Remove the 2 scrivets.
- Repeat to the other side.





10 Release the seat heating module bracket.
- Remove the 2 nuts.





11
NOTE:
Left hand shown, right hand similar.
Remove the RH wiring harness cover.
- Remove the 3 clips.

12 Remove the A-pillar trim panel. For additional information, refer to A-Pillar Trim Panel A-Pillar Trim Panel





13
NOTE:
The left hand front camera wiring harness connectors are colored white, the right hand front camera wiring harness connectors are colored black.
Disconnect the parking aid camera wiring harness.





14
NOTE:
The left hand front camera wiring harness connectors are colored white, the right hand front camera wiring harness connectors are colored black.
Disconnect the parking aid camera wiring harness.

Installation





1
NOTE:
Some variation in the illustrations may occur, but the essential information is always correct.
Remove the connector from the module end of the camera overlay wiring harness.
- Remove the locking tab.
- Carefully release the clip.
- Apply suitable tape to protect the end of the camera overlay wiring harness.




2
CAUTION: Make sure that the camera overlay wiring harness is not bent excessively during this procedure. Failure to follow this instruction may result in damage to the harness.
Install the camera overlay wiring harness.




3 Insert the camera wiring harness under the floor console.
- Route the camera overlay wiring harness along the main body wiring harness up to the camera module.




4 Install the connector to the camera overlay wiring harness.
- Remove the protective tape.
- Install the electrical connector.
- Secure the locking tab.




5
NOTE:
The left hand front camera wiring harness connectors are colored white, the right hand front camera wiring harness connectors are colored black.
Connect the camera overlay wiring harness.




6
CAUTION: Make sure that any tie straps used are not tightened excessively on the camera wiring harness and link leads, Failure to follow this instruction may result in damage to the harness.
Using suitable tie straps, secure the camera overlay wiring harness to the main body wiring harness.




7
NOTE:
The left hand front camera wiring harness connectors are colored white, the right hand front camera wiring harness connectors are colored black.
Connect the camera overlay wiring harness.
8 Install the A-pillar trim panel. For additional information, refer to A-Pillar Trim Panel A-Pillar Trim Panel




9
NOTE:
Left hand shown, right hand similar.
Install the RH wiring harness cover.
- Secure the 3 clips.





10 Secure the seat heating module bracket.
- Install the 2 nuts.





11 Install the parking aid camera module cover.
- Install the 2 scrivets.





12 Install the B-pillar floor covering trim panel.
- Secure the 2 clips.
- Repeat to the other side.

13 Install the front scuff plate trim panel.
- Secure the 7 clips.
- Repeat to the other side.





14 With assistance, install the LH front seat.
- Connect the 4 electrical connectors.

15 Install the RH front seat. For additional information, refer to Front Seat Front Seat





16
NOTE:
Make sure the 3 seat rail covers are fitted to their original positions. Note: The inner front seat rail does not have a seat rail cover.
Install the 2 front bolts to the front seat.
- Align the front seat locating pegs.
- Position the front seat fully rearwards.
- Tighten the front seat front bolts to 45 Nm.





17
NOTE:
Make sure the 3 seat rail covers are fitted to their original positions. Note: The inner front seat rail does not have a seat rail cover.
Install the 2 rear bolts to the front seat.
- Position the front seat fully forwards.
- Tighten the front seat rear bolts to 45 Nm.

18 Install the LH B-pillar upper trim panel. For additional information, refer to B-Pillar Trim Panel B-Pillar Trim Panel





19
CAUTION: Make sure the safety belt is secure and correctly installed.
Install the RH B-pillar trim panel.





20
NOTE:
Make sure the safety belt is operating correctly.
Secure the B-pillar trim panel.
- Secure the 4 clips.
- Secure the front and rear door aperture weatherstrips.





21 Attach the safety belt lower anchor to the seat.
- Install a new bolt and tighten to 45 Nm.





22 Install the safety belt lower anchor bolt cover.