Installation

INSTRUMENT PANEL: INSTRUMENT PANEL SAFETY PAD:

INSTALLATION

1. INSTALL INSTRUMENT PANEL ASSEMBLY
(a) Connect each of the clamps and connectors.
(b) Install the 2 bolts [A], bolt [B] and 2 nuts [D] as shown in the illustration below, then install the instrument panel assembly.





Torque: 20 Nm (204 kgf-cm, 15 ft-lbf)(Bolt [B])
2. INSTALL INSTRUMENT PANEL NO.1 REGISTER ASSEMBLY LOWER






(a) Engage the 3 clips and 2 claws, and install the instrument panel No.1 register assembly lower.
3. INSTALL INSTRUMENT PANEL NO.1 REGISTER ASSEMBLY






(a) Engage the 2 clips and 2 claws.
(b) Install the screw [C], nut [D], and the instrument panel No.1 register assembly.
4. INSTALL INSTRUMENT PANEL FINISH PLATE
5. INSTALL FRONT PILLAR GARNISH LH Installation

6. INSTALL FRONT PILLAR GARNISH RH
HINT: Use the same procedures for the RH side and the LH side.

7. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER CENTER






(a) Engage the 2 clips.
(b) Install the 7 screws [C] and the instrument panel finish panel lower center.
8. INSTALL FLOOR CARPET COVER CENTER LH






(a) Slide the floor carpet cover center LH to the rear of the vehicle, and engage the 2 claws to the instrument panel finish panel lower center at the floor carpet cover center LH.
(b) Install the 2 clips and the floor carpet cover center LH.
9. INSTALL FLOOR CARPET COVER CENTER RH
HINT: Use the same procedures for the RH side and the LH side.

10. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY






(a) Connect the connector.
(b) Install the 2 bolts [A], the 2 screws [C], and the glove compartment door assembly.
11. INSTALL INSTRUMENT PANEL NO.2 UNDER COVER SUB-ASSEMBLY






(a) Connect the connectors.
(b) Engage the 3 claws and install the instrument panel No.2 under cover sub-assembly.
12. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
HINT: Use the same procedures for the RH side and the LH side.

13. INSTALL FRONT DOOR SCUFF PLATE RH
HINT: Use the same procedures for the RH side and the LH side.

14. INSTALL COMBINATION METER ASSEMBLY






(a) Connect the connectors.
(b) Install the 4 screws [C] and the combination meter assembly.
15. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY






(a) Engage the 4 clips and install the instrument cluster finish panel sub-assembly.
16. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY Installation

17. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER






(a) Connect the connectors.
(b) Engage the 5 claws and the 4 clips.
(c) Connect the hood lock control cable assembly.
(d) Install the bolt [A], the screw [C], and the instrument panel finish panel sub-assembly lower.
18. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH






(a) Install the 2 clips and the cowl side trim sub-assembly LH.
19. INSTALL FRONT DOOR SCUFF PLATE LH Installation

20. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY Installation

21. INSTALL TILT AND TELESCOPIC SWITCH (w/ Power Tilt and Power Telescopic) Installation

22. INSTALL STEERING COLUMN COVER Installation

23. INSTALL STEERING WHEEL ASSEMBLY Installation

24. INSTALL STEERING PAD Installation

25. INSTALL STEERING WHEEL NO.3 COVER LOWER Installation

26. INSTALL STEERING WHEEL NO.2 COVER LOWER Installation

27. INSTALL MULTI-DISPLAY (w/ Navigation System) Installation

28. INSTALL CENTER CLUSTER INTEGRATION SWITCH (w/o Navigation System) Installation

29. INSTALL RADIO RECEIVER Installation

30. INSTALL INSTRUMENT PANEL FINISH PANEL LOWER






(a) Connect the connectors.
(b) Engage the 2 clips and install the instrument panel finish panel lower.
31. INSTALL CONSOLE PANEL UPPER FRONT






(a) Engage the 4 clips and install the console panel upper front.
32. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY
33. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
34. PERFORM INITIALIZATION
NOTE: Some systems need initialization when disconnecting the cable from the negative battery terminal Repair Instruction - Initialization.

35. INSPECT STEERING PAD Installation

36. INSPECT SRS WARNING LIGHT
Diagnosis System