Installation

STEERING COLUMN: STEERING COLUMN ASSEMBLY: INSTALLATION

1. INSTALL STEERING COLUMN ASSEMBLY

(a) Install the steering column assembly with the 4 nuts.

Torque : 26 Nm (260 kgf-cm, 19 ft-lbf)

(b) Connect the connectors and wire harness clamps to the steering column assembly.

2. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

(a) Install the clamp to the steering column hole cover.

(b) Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering column.

Align the matchmarks on the No. 2 steering intermediate shaft assembly and the steering link.

(d) Install the bolt.

Torque : 35 Nm (360 kgf-cm, 26 ft-lbf)

3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

4. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY

(a) Attach the 2 claws to install the air duct.

(b) Install the bolt.

Torque : 9.8 Nm (100 kgf-cm, 87 in-lbf)

Attach the 2 claws and install the wiring harness protector.

5. INSTALL NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY Installation

6. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY Installation

7. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Installation

8. INSTALL INSTRUMENT PANEL FINISH PANEL END LH Installation

9. INSTALL NO. 1 INSTRUMENT CLUSTER MOULDING Installation

10. INSTALL INSTRUMENT SIDE PANEL LH Installation

11. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY Installation

12. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

(a) Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.

(b) Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.

13. INSTALL TILT AND TELESCOPIC SWITCH

(a) Attach the claw to install the switch.

(b) Connect the switch connector.

14. INSTALL STEERING COLUMN COVER (w/o Driver Monitor Camera)

(a) Attach the claw to install the upper steering column cover.

(b) Attach the 4 clips to install the upper steering column cover onto the instrument cluster finish panel.

(c) Attach the 2 claws to install the lower steering column cover.

NOTICE:
Do not damage the tilt and telescopic switch.

(d) Install the 3 screws.

Torque : 2.0 Nm (20 kgf-cm, 18 in-lbf)

15. INSTALL STEERING COLUMN COVER (w/ Driver Monitor Camera)

(a) Connect the driver monitor connector.

(b) Attach the claw to install the upper steering column cover.

(c) Attach the 4 clips to install the upper steering column cover onto the instrument cluster finish panel.

(d) Attach the 2 claws to install the lower steering column cover.

NOTICE:
Do not damage the tilt and telescopic switch.

(e) Install the 3 screws.

Torque : 2.0 Nm (20 kgf-cm, 18 in-lbf)

16. ADJUST SPIRAL CABLE SUB-ASSEMBLY Installation

17. INSTALL STEERING WHEEL ASSEMBLY

(a) Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

(b) Install the steering wheel assembly set nut.

Torque : 50 Nm (510 kgf-cm, 37 ft-lbf)

18. INSPECT STEERING WHEEL CENTER POINT

19. INSPECT STEERING PAD

(a) Inspect the steering pad Steering Pad.

20. INSTALL STEERING WHEEL PAD Installation

21. INSTALL NO. 2 STEERING WHEEL COVER LOWER Installation

22. INSTALL SWITCH AND VOLUME CASE Installation

23. CHECK FRONT WHEELS FACING STRAIGHT AHEAD

24. INSTALL FRONT WHEELS

Torque : 140 Nm (1428 kgf-cm, 103 ft-lbf)

25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
* Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter Programming and Relearning.
* When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

26. INSTALL BATTERY SERVICE HOLE COVER LH Removal

27. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire) Installation

28. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY Installation

29. INSPECT SRS WARNING LIGHT

(a) Inspect the SRS warning light Diagnosis System.