Operation CHARM: Car repair manuals for everyone.

B1637





SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: B1627/82, B1628/82, B1637/82, B1638/82, B1647/82, B1648/82: Lost Communication with Front Passenger Side - Side Airbag Sensor Assembly
B1648/82 - Front Passenger Side Satellite Sensor Bus Initialization Incomplete

DESCRIPTION

The front passenger side - side collision sensor circuit (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH) is composed of the center airbag sensor assembly, side airbag sensor RH, and rear airbag sensor RH.

The side airbag sensor RH and rear airbag sensor RH detect impacts to the vehicle and send signals to the center airbag sensor assembly to determine if the airbag should be deployed.

These DTCs are recorded when a malfunction is detected in the circuit for the front passenger side - side collision sensor (to determine deployment of the front seat side airbag assembly RH and curtain shield airbag assembly RH).





WIRING DIAGRAM





INSPECTION PROCEDURE

PROCEDURE

1. CHECK PRESENT DTC

(a) Turn the engine switch on (IG), and wait for at least 60 seconds.





(b) Check for present DTCs DTC Check / Clear.

Result:





HINT
* DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the engine switch off and then on (IG) again.
* Codes other than present DTC B1627, B1628, B1637, B1638, B1647, B1648, and 82 may be output at this time, but they are not related to this check.

B -- CHECK CONNECTORS

C -- CHECK CONNECTORS

D -- CHECK REAR AIRBAG SENSOR RH

E -- USE SIMULATION METHOD TO CHECK Diagnosis System
A -- Continue to next step.

2. CHECK PAST DTC

(a) Check for past DTCs DTC Check / Clear.

Result:





HINT
Codes other than past DTC B1627 and B1637 may be output at this time, but they are not related to this check.

B -- CHECK CONNECTORS

C -- CHECK REAR AIRBAG SENSOR RH
A -- Continue to next step.

3. CHECK CONNECTORS

(a) Turn the engine switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Check that the connectors are properly connected to the center airbag sensor assembly, rear airbag sensor RH and the side airbag sensor RH.

OK:

The connectors are properly connected.

HINT
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

(d) Disconnect the connectors from the center airbag sensor assembly, rear airbag sensor RH and side airbag sensor RH.

(e) Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.

NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

4. CHECK FLOOR WIRE (OPEN)

(a) Using SST, connect terminals 8 (BCP+) and 11 (BCP-) of connector B.





NOTICE:
Do not forcibly insert SST into the terminals of the connector when connecting.

SST : 09843-18040

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

5. CHECK FLOOR WIRE (SHORT)

(a) Disconnect SST from connector B.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

6. CHECK FLOOR WIRE (SHORT TO B+)

(a) Connect the cable to the negative (-) battery terminal.





(b) Turn the engine switch on (IG).

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:





NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

7. CHECK FLOOR WIRE (SHORT TO GROUND)

(a) Turn the engine switch off.





(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

8. CHECK FLOOR WIRE (OPEN)

(a) Using SST, connect terminals 2 (BBR+) and 1 (BBR-) of connector C.





NOTICE:
Do not forcibly insert SST into the terminals of the connector when connecting.

SST : 09843-18040

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

9. CHECK FLOOR WIRE (SHORT)

(a) Disconnect SST from connector C.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

10. CHECK FLOOR WIRE (SHORT TO B+)

(a) Connect the cable to the negative (-) battery terminal.





(b) Turn the engine switch on (IG).

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:





NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

11. CHECK FLOOR WIRE (SHORT TO GROUND)

(a) Turn the engine switch off.





(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

12. CHECK REAR AIRBAG SENSOR RH

(a) Connect the connectors to the side airbag sensor RH and the center airbag sensor assembly.





(b) Interchange the rear airbag sensor LH with RH and connect the connectors.

(c) Connect the cable to the negative (-) battery terminal.

(d) Turn the engine switch on (IG), and wait for at least 60 seconds.

(e) Clear the DTCs stored in the memory DTC Check / Clear.

(f) Turn the engine switch off.

(g) Turn the engine switch on (IG), and wait for at least 60 seconds.

(h) Check for DTCs DTC Check / Clear.

Result:





HINT
Codes other than DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 may be output at this time, but they are not related to this check.

B -- REPLACE REAR AIRBAG SENSOR RH Removal

C -- USE SIMULATION METHOD TO CHECK Diagnosis System
A -- Continue to next step.

13. CHECK SIDE AIRBAG SENSOR RH

(a) Turn the engine switch off.





(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Return the rear airbag sensor LH and RH to their original positions and connect the connectors.

(d) Interchange the side airbag sensor LH with RH and connect the connectors.

(e) Connect the cable to the negative (-) battery terminal.

(f) Turn the engine switch on (IG), and wait for at least 60 seconds.

(g) Clear the DTCs stored in the memory DTC Check / Clear.

(h) Turn the engine switch off.

(i) Turn the engine switch on (IG), and wait for at least 60 seconds.

(j) Check for DTCs DTC Check / Clear.

Result:





HINT
Codes other than DTC B1623, B1642, B1643, or 81 and B1628, B1647, B1648, or 82 may be output at this time, but they are not related to this check.

B -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY Removal

C -- REPLACE SIDE AIRBAG SENSOR RH Removal

A -- USE SIMULATION METHOD TO CHECK Diagnosis System

14. CHECK CONNECTORS

(a) Turn the engine switch off.

(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Check that the connectors are properly connected to the side airbag sensor RH and the rear airbag sensor RH.

OK:

The connectors are properly connected.

HINT
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

(d) Disconnect the connectors from the side airbag sensor RH and rear airbag sensor RH.

(e) Check that the terminals of connectors are not damaged.

OK:

The terminals are not deformed or damaged.

NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

15. CHECK FLOOR WIRE (OPEN)

(a) Using SST, connect terminals 2 (BBR+) and 1 (BBR-) of connector C.





NOTICE:
Do not forcibly insert SST into the terminals of the connector when connecting.

SST : 09843-18040

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

16. CHECK FLOOR WIRE (SHORT)

(a) Disconnect SST from connector C.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

17. CHECK FLOOR WIRE (SHORT TO B+)

(a) Connect the cable to the negative (-) battery terminal.





(b) Turn the engine switch on (IG).

(c) Measure the voltage according to the value(s) in the table below.

Standard Voltage:





NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

18. CHECK FLOOR WIRE (SHORT TO GROUND)

(a) Turn the engine switch off.





(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPLACE FLOOR WIRE
OK -- Continue to next step.

19. CHECK REAR AIRBAG SENSOR RH

(a) Connect the connector to the side airbag sensor RH.





(b) Interchange the rear airbag sensor LH with RH and connect the connectors.

(c) Connect the cable to the negative (-) battery terminal.

(d) Turn the engine switch on (IG), and wait for at least 60 seconds.

(e) Clear the DTCs stored in the memory DTC Check / Clear.

(f) Turn the engine switch off.

(g) Turn the engine switch on (IG), and wait for at least 60 seconds.

(h) Check for DTCs DTC Check / Clear.

Result:





HINT
Codes other than DTC B1632 or B1633 and B1637 or B1638 may be output at this time, but they are not related to this check.

B -- REPLACE REAR AIRBAG SENSOR RH Removal

C -- USE SIMULATION METHOD TO CHECK Diagnosis System
A -- Continue to next step.

20. CHECK SIDE AIRBAG SENSOR RH

(a) Turn the engine switch off.





(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Return the rear airbag sensor LH and RH to their original positions and connect the connectors.

(d) Interchange the side airbag sensor LH with RH and connect the connectors.

(e) Connect the cable to the negative (-) battery terminal.

(f) Turn the engine switch on (IG), and wait for at least 60 seconds.

(g) Clear the DTCs stored in the memory DTC Check / Clear.

(h) Turn the engine switch off.

(i) Turn the engine switch on (IG), and wait for at least 60 seconds.

(j) Check for DTCs DTC Check / Clear.

Result:





HINT
Codes other than DTC B1632 or B1633 and B1637 or B1638 may be output at this time, but they are not related to this check.

B -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY Removal

C -- REPLACE SIDE AIRBAG SENSOR RH Removal

A -- USE SIMULATION METHOD TO CHECK Diagnosis System

21. CHECK REAR AIRBAG SENSOR RH

(a) Turn the engine switch off.





(b) Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

(c) Interchange the rear airbag sensor LH with RH and connect the connectors.

(d) Connect the cable to the negative (-) battery terminal.

(e) Turn the engine switch on (IG), and wait for at least 60 seconds.

(f) Clear the DTCs stored in the memory DTC Check / Clear.

(g) Turn the engine switch off.

(h) Turn the engine switch on (IG), and wait for at least 60 seconds.

(i) Check for DTCs DTC Check / Clear.

Result:





HINT
Codes other than DTC B1622 and B1627 may be output at this time, but they are not related to this check.

B -- REPLACE CENTER AIRBAG SENSOR ASSEMBLY Removal

C -- REPLACE REAR AIRBAG SENSOR RH Removal

A -- USE SIMULATION METHOD TO CHECK Diagnosis System