ECM Power Source Circuit

2UR-FSE ENGINE CONTROL SYSTEM: SFI SYSTEM: ECM Power Source Circuit
- ECM Power Source Circuit

DESCRIPTION

When the power switch is turned on (IG), the battery voltage is applied to terminal IGSW of the ECM. The ECM MREL output signal causes a current to flow to the coil, closing the contacts of the EFI relay (EFI MAIN2) and supplying power to terminal +B and +B2 of the ECM.

If the power switch is turned off, the ECM holds the EFI relay (EFI MAIN2) ON for a maximum of 2 seconds to allow for the initial setting of the throttle valve.

When the power switch is turned on (IG), voltage from the ECM's MREL terminal is applied to the EFI relay (EFI MAIN2). This causes the contacts of the EFI relay (EFI MAIN2) to close, which supplies power to terminal +B and +B2 of the ECM.

WIRING DIAGRAM





INSPECTION PROCEDURE

PROCEDURE

1. INSPECT ECM (+B, +B2 VOLTAGE)

(a) Turn the power switch on (IG).





(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:





NG -- CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

OK -- PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE Symptom Related Diagnostic Procedures

2. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

(a) Disconnect the E3 ECM connector.





(b) Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.

3. INSPECT ECM (IGSW VOLTAGE)

(a) Turn the power switch on (IG).





(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:





OK -- INSPECT ECM (MREL VOLTAGE)

NG -- INSPECT FUSE (ECU-IG)

4. INSPECT FUSE (ECU-IG)

(a) Remove the ECU-IG fuse from the engine room No. 2 junction block.





(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NG -- CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK -- Continue to next step.

5. INSPECT IGNITION RELAY NO. 2 (IG2)

(a) Inspect the IG2 relay Ignition Relay No. 2.

NG -- REPLACE IGNITION RELAY NO. 2 (IG2) Ignition Relay No. 2

OK -- GO TO SMART ACCESS SYSTEM WITH PUSH-BUTTON START Power Source Mode does not Change

6. INSPECT ECM (MREL VOLTAGE)

(a) Turn the power switch on (IG).





(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:





NG -- REPLACE ECM Removal
OK -- Continue to next step.

7. INSPECT FUSE (EFI MAIN2)

(a) Remove the EFI MAIN2 fuse from the engine room No. 2 relay block.





(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:





NG -- CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK -- Continue to next step.

8. INSPECT EFI RELAY (EFI MAIN2)

(a) Inspect the EFI MAIN2 relay EFI Relay.

NG -- REPLACE EFI RELAY (EFI MAIN2) EFI Relay
OK -- Continue to next step.

9. CHECK HARNESS AND CONNECTOR (EFI RELAY (EFI MAIN2) - ECM, BODY GROUND)





(a) Check the harness and the connectors between the integration relay and ECM.

(1) Remove the EFI MAIN2 relay from the engine room No. 2 relay block.

(2) Disconnect the A14 ECM connector.

(3) Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):





Standard resistance (Check for short):





(b) Check the harness and the connectors between the EFI MAIN2 relay and body ground.

(1) Remove the EFI MAIN2 relay from the engine room No. 2 relay block.

(2) Measure the resistance according to the value(s) in the table below.

Standard resistance (Check for open):





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR

OK -- CHECK AND REPAIR HARNESS OR CONNECTOR (TERMINAL +B OF ECM - BATTERY POSITIVE TERMINAL)