Operation CHARM: Car repair manuals for everyone.
Home >> Nissan-Datsun >> 2009 >> Versa L4-1.8L (MR18DE) >> Repair and Diagnosis >> Body and Frame >> Interior Moulding / Trim >> Dashboard / Instrument Panel >> Service and Repair >> Removal and Replacement >> Removal And Installation

Removal And Installation





INSTRUMENT PANEL ASSEMBLY


Removal and Installation


INSTRUMENT PANEL ASSEMBLY

Removal
1. Pull instrument finisher E backward by approximately 30 degrees while disengaging the instrument finisher E metal clips and pawl.
: Broken Square indicates Metal Clip





: Broken Circle indicates Pawl




2. Remove cluster lid C.

: Broken Square indicates Metal Clip
: Broken Circle indicates Pawl

a. Remove cluster lid C screws.
b. Pull back and disengage pawls and cluster lid C metal clips.
c. Disconnect harness connector and then remove cluster lid C.
3. Remove audio unit. Refer to Service and Repair.
4. Remove front pillar garnish. Refer to Component.





5. Remove the side panel (LH/RH).
: Broken Circle indicates Pawl

a. Pull up instrument side panel and disengage pawls.
b. Remove instrument side panel.





6. Remove instrument side mask (LH/RH).
: Broken Circle indicates Pawl

a. Insert a suitable tool into upper space of instrument mask.
b. Disengage pawls, and then remove instrument side mask.





7. Remove instrument side finisher.
: Broken Square indicates Metal Clip

a. Insert a suitable tool into space of instrument side finisher.
b. Disengage instrument side finisher metal clips, and then remove instrument side finisher.





8. Remove side ventilator assembly (LH).
: Broken Circle indicates Pawl

a. Insert a suitable tool into the bottom gap of side ventilator assembly after removing the instrument side mask and push against A and B as shown to disengage the pawls.





b. Lift the side ventilator up from the bottom, pull backward while disengaging the side ventilator assembly upper pawls, and then remove the side ventilator.
: Broken Circle indicates Pawl
9. Remove steering lock escutcheon.
10. Remove screws, and disengage pawls then remove the steering column cover.





11. Remove cluster lid A.
a. Remove screws from instrument upper panel right side.





b. Lift the instrument upper panel up, disengage metal clips.
: Broken Square indicates Metal Clip
: Broken Triangles Indicate Clip

c. Pull backward and disengage clips.
d. Remove cluster lid A.
12. Remove combination meter. Refer to .





13. Remove instrument lower finisher.
: Broken Square indicates Metal Clip
: Broken Circle indicates Pawl

a. Disengage pawls and remove fuse block lid.
b. Remove the screws.
c. Pull backward while disengaging the instrument lower finisher clip and pawls.
d. Disconnect in-vehicle sensor and harness connector, and then remove instrument lower finisher.
14. Remove glove box. Refer to Disassembly and Assembly.





15. Remove side ventilator assembly.
: Broken Square indicates Metal Clip
: Broken Circle indicates Pawl

a. Insert a suitable tool into the side ventilator assembly from center console side, disengage the clips and pawl of instrument panel pad.





b. Reach through the glove box compartment by hand to the backside of the side ventilator and push against A as shown to engage the pawl.
: Broken Circle indicates Pawl

c. Insert a suitable tool into the bottom gap of side ventilator assembly after removing the instrument side mask and push against B as shown to disengage the pawl.





d. Lift the side ventilator assembly up from the bottom, pull backward while disengaging the side ventilator assembly upper pawls, and then remove the side ventilator assembly.
: Broken Circle indicates Pawl
16. Remove front passenger air bag module. Refer to Front Passenger Air Bag Module.





17. Remove instrument upper mask.
: Broken Circle indicates Pawl

a. Insert a remover into backside space of instrument upper mask.
b. Disconnect harness connector, and then remove instrument upper mask.





18. Remove instrument finisher D.
: Broken Circle indicates Pawl
: Broken Triangles Indicate Clip

a. Insert a remover into upper space of instrument finisher D.
b. Disengage clips and pawls, then remove instrument finisher D.
19. Remove controller. Refer to Removal and Replacement.





20. Remove instrument upper panel assembly.

: Broken Square indicates Metal Clip
a. Remove bolts and screws.
b. Pull backward and remove instrument upper panel assembly.

21. Remove lighting and turn signal switch. Refer to Service and Repair.
22. Remove wiper and washer switch. Refer to Service and Repair.
23. Remove hood opener handle and fuel filler lid opener handle. Refer to Service and Repair.
24. Remove screws, and then remove instrument panel and pad from passenger door opening portion.

Installation
Installation is in the reverse order of removal.

CLUSTER LID A

Removal




1. Pull instrument finisher E backward by approximately 30 degrees while disengaging the metal clips and pawl.

: Broken Square indicates Metal Clip
: Broken Circle indicates Pawl

2. Remove front pillar garnish. Refer to Component.





3. Pull up instrument side panel and disengage pawls.
: Broken Circle indicates Pawl
4. Remove instrument side panel.





5. Insert a remover into upper space of instrument mask.
: Broken Circle indicates Pawl
6. Disengage pawls, and then remove instrument side mask.





7. Insert a remover into space of instrument side finisher.
: Broken Square indicates Metal Clip
8. Disengage metal clips, and then remove instrument side finisher.





9. Insert suitable tool into the bottom gap of side ventilator assembly after removing the instrument side mask, push against A and B as shown to disengage the pawls.
: Broken Circle indicates Pawl





10. Lift the side ventilator up from the bottom, pull backward while disengaging the side ventilator assembly's upper pawls, and then remove the side ventilator.
: Broken Circle indicates Pawl
11. Remove screws, and disengage pawls.
12. Remove steering column cover upper.





13. Remove screws from instrument upper panel right side.




14. Lift the instrument upper panel up, disengage metal clips.

: Broken Square indicates Metal Clip
: Broken Triangles Indicate Clip

15. Pull backward and disengage clips.
16. Remove cluster lid A.

Installation
Installation is in the reverse order of removal.

CLUSTER LID C

Removal




1. Pull instrument finisher E backward by approximately 30 degrees while disengaging the metal clips and pawl.

: Broken Square indicates Metal Clip
: Broken Circle indicates Pawl





2. Remove screws.
3. Pull back, and disengage pawls and metal clips.
4. Disconnect harness connector, and then remove cluster lid C.

Installation
Installation is in the reverse order of removal.

COMBINATION METER

Removal




1. Pull instrument finisher E backward by approximately 30 degrees while disengaging the metal clips and pawl.


: Broken Square indicates Metal Clip
: Broken Circle indicates Pawl
2. Remove front pillar garnish. Refer to Component.





3. Pull up instrument side panel and disengage pawls.
: Broken Circle indicates Pawl
4. Remove instrument side panel.





5. Insert a remover into upper space of instrument mask.
: Broken Circle indicates Pawl
6. Disengage pawls, and then remove instrument side mask.





7. Insert a remover into space of instrument side finisher.
: Broken Square indicates Metal Clip
: Broken Circle indicates Pawl
8. Disengage metal clips, and then remove instrument side finisher.





9. Insert suitable tool into the bottom gap of side ventilator assembly after removing the instrument side mask, push against A and B as shown to disengage the pawls.
: Broken Circle indicates Pawl





10. Lift the side ventilator up from the bottom, pull backward while disengaging the side ventilator assembly's upper pawls, and then remove the side ventilator.
: Broken Circle indicates Pawl
11. Remove screws, and disengage pawls.
12. Remove steering column cover upper.





13. Remove screws from instrument upper panel right side.




14. Lift the instrument upper panel up, disengage metal clips.


: Broken Square indicates Metal Clip
: Broken Triangles Indicate Clip
15. Pull backward and disengage clips.
16. Remove cluster lid A.





17. Remove screws (A) and metal clip (B), and remove combination meter.

Installation
Installation is in the reverse order of removal.

GLOVE BOX ASSEMBLY

Removal




1. Remove glove box screws.
2. Pull backward while disengaging the glove box assembly pawls.
3. Disconnect lamp harness connector, and then remove glove box assembly.

Installation
Installation is in the reverse order of removal.

INSTRUMENT LOWER FINISHER

Removal




1. Pull backward while disengage the instrument lower finisher's clip and pawls.


: Broken Square indicates Metal Clip
2. Disconnect in-vehicle sensor and harness connector, and then remove instrument lower finisher.

Installation
Installation is in the reverse order of removal.

CENTER CONSOLE ASSEMBLY

Removal




1. Insert a suitable tool into front side space of console mask, and disengage metal clips.


: Broken Square indicates Metal Clip
2. Disconnect harness connector, and then remove console mask.
3. Place the selector lever in "D" position (A/T and CVT only).





: Broken Square indicates Metal Clip
4. Remove selector lever knob (A/T and CVT only). Refer to Shift Control System (CVT), Removal and Replacement (A/T).
5. Pull up and disengage A/T and CVT console finisher metal clips (A/T and CVT only).
6. Remove A/T and CVT console finisher (A/T and CVT only).
7. Remove shift knob (M/T only). Refer to Shift Control.
8. Pull up and disengage M/T console boot metal clips (M/T only).
9. Remove M/T console boot (M/T only).





10. Disengage console rear finisher metal clips and pawl.
: Broken Square indicates Metal Clip
: Broken Circle indicates Pawl
11. Remove console rear finisher.





12. Disengage console mask cover metal clips and pawls, and then remove console mask cover (with armrest).
: Broken Square indicates Metal Clip
: Broken Circle indicates Pawl





13. Disengage rear cup holder metal clips and pawls (without armrest).
: Broken Square indicates Metal Clip
: Broken Circle indicates Pawl
14. Remover rear cup holder (without armrest).
15. Remove console body assembly screws and nut.
16. Disconnect harness connector, and then remove console body assembly.





17. Remove both of the instrument lower cover LH and RH clips.
: Broken Square indicates Metal Clip
18. Disengage instrument lower cover LH and RH metal clips and remove both of the instrument lower cover LH and RH.
19. Remove screws and then remove center console.

Installation
Installation is in the reverse order of removal.
pro multis · About Operation CHARM