Back Door

ENGINE HOOD / DOOR: BACK DOOR: ADJUSTMENT

ADJUSTMENT
HINT:
- Use the same procedure for the RH side and LH side.





- The following procedure is for the LH side.
- Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts installed. Substitute the centering bolts with standard bolts (with washers) when making adjustments.
- A bolt without a torque specification is shown in the standard bolt chart.

1. PRECAUTION
NOTICE:
- For the glass hatch type, if the back door adjustment is performed, the location of the axis of the rear wiper motor assembly will change, causing the wiping angle to change. Be sure to remove and install the rear wiper motor assembly using the centering jig.
- Do not open the glass hatch before installing the rear wiper link pivot.

2. REMOVE DECK BOARD ASSEMBLY Removal Part 1, Step 1-62

3. REMOVE NO. 3 DECK BOARD SUB-ASSEMBLY Removal Part 1, Step 1-62

4. REMOVE NO. 2 DECK BOARD SUB-ASSEMBLY Removal Part 1, Step 1-62

5. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) Removal Part 1, Step 1-62

6. REMOVE REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat) Removal Part 1, Step 1-62

7. REMOVE REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat) Removal Part 1, Step 1-62

8. REMOVE DECK SIDE TRIM BOX LH Removal Part 1, Step 1-62

9. REMOVE REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat) Removal Part 1, Step 1-62

10. REMOVE JACK CARRIER SUPPORT
11. REMOVE JACK CARRIER CUSHION Removal Part 1, Step 1-62

12. REMOVE JACK ASSEMBLY Removal Part 1, Step 1-62

13. REMOVE JACK CARRIER ASSEMBLY Removal Part 1, Step 1-62

14. REMOVE DECK SIDE TRIM BOX RH Removal Part 1, Step 1-62

15. REMOVE DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat) Removal Part 1, Step 1-62

16. REMOVE REAR MAT Removal Part 1, Step 1-62

17. REMOVE DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat) Removal Part 1, Step 1-62

18. REMOVE REAR DECK FLOOR BOX (w/o Rear No. 2 Seat) Removal Part 1, Step 1-62

19. REMOVE REAR FLOOR FINISH PLATE Removal Part 1, Step 1-62

20. ADJUST BACK DOOR PANEL SUB-ASSEMBLY






(a) Before adjusting the upper end of the back door up and down or left and right, loosen the bolts.
(b) Tighten the body side hinge after the adjustment.
Torque: 20 Nm (204 kgf-cm, 15 ft-lbf)






(c) Adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic hammer.
(d) Tighten the striker mounting screws after the adjustment.
Torque: 23 Nm (235 kgf-cm, 17 ft-lbf)
21. INSTALL REAR FLOOR FINISH PLATE Installation Part 1, Step 1-65

22. INSTALL REAR DECK FLOOR BOX (w/o Rear No. 2 Seat) Installation Part 1, Step 1-65

23. INSTALL DECK FLOOR BOARD ASSEMBLY (w/o Rear No. 2 Seat) Installation Part 1, Step 1-65

24. INSTALL REAR MAT Installation Part 1, Step 1-65

25. INSTALL DECK FLOOR BOARD ASSEMBLY (w/ Rear No. 2 Seat) Installation Part 1, Step 1-65

26. INSTALL DECK SIDE TRIM BOX LH Installation Part 1, Step 1-65

27. INSTALL REAR SEAT SIDE COVER LH (w/ Rear No. 2 Seat) Installation Part 1, Step 1-65

28. INSTALL DECK SIDE TRIM BOX RH Installation Part 1, Step 1-65

29. INSTALL JACK CARRIER ASSEMBLY Installation Part 1, Step 1-65

30. INSTALL JACK ASSEMBLY Installation Part 1, Step 1-65

31. INSTALL JACK CARRIER CUSHION Installation Part 1, Step 1-65

32. INSTALL JACK CARRIER SUPPORT
33. INSTALL REAR SEAT SIDE COVER RH (w/ Rear No. 2 Seat) Installation Part 1, Step 1-65

34. INSTALL REAR NO. 1 FLOOR BOARD (w/o Rear No. 2 Seat) Installation Part 1, Step 1-65

35. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) Installation Part 1, Step 1-65

36. INSTALL NO. 2 DECK BOARD SUB-ASSEMBLY Installation Part 1, Step 1-65

37. INSTALL NO. 3 DECK BOARD SUB-ASSEMBLY Installation Part 1, Step 1-65

38. INSTALL DECK BOARD ASSEMBLY Installation Part 1, Step 1-65

39. REMOVE BACK WINDOW UPPER TRIM PANEL ASSEMBLY Disassembly

40. REMOVE BACK DOOR TRIM COVER LH (w/o Power Back Door) Disassembly

41. REMOVE BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door) Disassembly

42. DISCONNECT POWER BACK DOOR ROD (w/ Power Back Door) Disassembly

43. REMOVE BACK DOOR TRIM COVER LH (w/ Power Back Door) Disassembly

44. REMOVE BACK DOOR TRIM COVER RH Disassembly

45. REMOVE BACK DOOR LOCK COVER (for Glass Hatch Type) Disassembly

46. REMOVE ASSIST STRAP HOLE COVER Disassembly

47. REMOVE ASSIST STRAP ASSEMBLY Disassembly

48. REMOVE BACK DOOR TRIM PANEL ASSEMBLY Disassembly

49. REMOVE REAR WIPER SHAFT COVER (for Glass Hatch Type)

50. REMOVE REAR WIPER ARM HEAD CAP

51. REMOVE REAR WIPER ARM AND BLADE ASSEMBLY

52. REMOVE REAR WIPER LINK CAP (for Glass Hatch Type)

53. REMOVE REAR WIPER LINK PIVOT (for Glass Hatch Type)

54. REMOVE REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)

55. INSTALL REAR WIPER MOTOR ASSEMBLY (for Glass Hatch Type)

56. INSTALL REAR WIPER LINK PIVOT (for Glass Hatch Type)

57. INSTALL REAR WIPER LINK CAP (for Glass Hatch Type)

58. INSTALL REAR WIPER ARM AND BLADE ASSEMBLY (for Glass Hatch Type)

59. INSTALL REAR WIPER ARM HEAD CAP

60. INSTALL REAR WIPER SHAFT COVER (for Glass Hatch Type)

61. INSTALL BACK DOOR TRIM PANEL ASSEMBLY Reassembly

62. INSTALL ASSIST STRAP ASSEMBLY Reassembly

63. INSTALL ASSIST STRAP HOLE COVER Reassembly

64. INSTALL BACK DOOR LOCK COVER (for Glass Hatch Type) Reassembly

65. INSTALL BACK DOOR TRIM COVER LH (w/o Power Back Door) Reassembly

66. INSTALL BACK DOOR TRIM COVER LH (w/ Power Back Door) Reassembly

67. CONNECT POWER BACK DOOR ROD (w/ Power Back Door) Reassembly

68. INSTALL BACK DOOR SERVICE HOLE COVER LH (w/ Power Back Door) Reassembly

69. INSTALL BACK DOOR TRIM COVER RH Reassembly

70. INSTALL BACK WINDOW UPPER TRIM PANEL ASSEMBLY Reassembly