Installation
U760E AUTOMATIC TRANSMISSION / TRANSAXLE: AUTOMATIC TRANSAXLE ASSEMBLY: INSTALLATION
1. INSTALL TRANSMISSION CASE PLUG ASSEMBLY
(a) Apply ATF to a new O-ring and install it onto the transmission case plug.
(b) Install the transmission case plug onto the automatic transaxle.
2. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
(a) Install the No. 1 transmission control cable bracket onto the automatic transaxle with the 2 bolts.
Torque : 12 Nm (122 kgf-cm, 9 ft-lbf)
3. INSTALL WIRE HARNESS CLAMP BRACKET
(a) Install the 5 wire harness clamp brackets onto the automatic transaxle with the 5 bolts.
Torque : 8.4 Nm (85 kgf-cm, 74 in-lbf)
4. INSTALL TCM
(a) Install the TCM onto the automatic transaxle.
(b) Install and tighten the 2 bolts in the order shown in the illustration.
Torque : 11 Nm (115 kgf-cm, 8 ft-lbf)
5. INSTALL FRONT ENGINE MOUNTING BRACKET
(a) Install the front engine mounting bracket onto the automatic transaxle with the 3 bolts.
Torque : 64 Nm (653 kgf-cm, 47 ft-lbf)
6. INSTALL FLEXIBLE HOSE BRACKET SUB-ASSEMBLY
(a) Install the flexible hose bracket onto the automatic transaxle with the bolt.
Torque : 20 Nm (204 kgf-cm, 15 ft-lbf)
7. CONNECT BREATHER PLUG HOSE
(a) Engage the clamp and connect the breather plug hose onto the flexible hose bracket.
8. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY
(a) Engage the splines of the input shaft and turbine runner.
(b) Engage the splines of the stator shaft and the stator while turning the torque converter.
HINT
If the stator shaft splines are difficult to engage with the stator splines, move the torque converter back approximately 10 mm (0.393 in.) and engage the splines while rotating the torque converter.
(c) Turn the torque converter to engage the key of the oil pump drive gear into the slot on the torque converter.
(d) Using a vernier caliper and a straightedge, measure dimension A between the transaxle fitting surface of the engine (*a) and the torque converter fitting surface of the drive plate (*b). [#1]
Text in Illustration
(e) Using a vernier caliper and a straightedge, measure dimension B shown in the illustration and check that dimension B is greater than dimension A, which was measured in step [#1].
Standard:
B = A + 1 mm (0.0394 in.) or more
NOTICE:
* Make sure to deduct the thickness of the straightedge.
* If the transaxle is installed to the engine with the torque converter not sufficiently inserted, the torque converter may be damaged.
9. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY
(a) Confirm that the 2 knock pins are on the automatic transaxle contact surface of the engine cylinder block before automatic transaxle installation.
Text in Illustration
(b) Apply clutch spline grease to the round of the crankshaft contact surface (*a) with the torque converter centerpiece.
Text in Illustration
Clutch spline grease:
Toyota Genuine Clutch Spline Grease or equivalent
Maximum spread:
Approximately 1 g (0.0353 oz)
(c) Keeping the engine and automatic transaxle in a horizontal position, align the knock pins with each hole on the automatic transaxle and tighten the 9 bolts shown in the illustration.
Bolt A - Torque : 64 Nm (653 kgf-cm, 47 ft-lbf)
Bolt B - Torque : 46 Nm (469 kgf-cm, 34 ft-lbf)
Bolt C - Torque : 43 Nm (438 kgf-cm, 32 ft-lbf)
Bolt Length
NOTICE:
* Do not twist or apply excessive force to the automatic transaxle.
* Check that the torque converter rotates smoothly after installation of the automatic transaxle.
10. CONNECT ENGINE WIRE
(a) Connect the TCM connector.
(b) Turn the lock lever and secure the connector with the lock lever.
Text in Illustration
(c) Engage the 4 clamps and connect the engine wire.
(d) Install the ground wire onto the automatic transaxle with the bolt.
Torque : 19 Nm (195 kgf-cm, 14 ft-lbf)
(e) Engage the 3 clamps and connect the engine wire.
(f) Connect the park/neutral position switch connector.
(g) Engage the clamp and connect the engine wire.
(h) Connect the air fuel ratio sensor connector.
(i) Engage the 2 clamps and connect the engine wire.
11. INSTALL STARTER ASSEMBLY Installation
12. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE
Installation
13. CHECK AUTOMATIC TRANSAXLE SYSTEM
NOTICE:
If automatic transmission parts have been replaced, refer to Parts Replacement Compensation Table to determine if any additional operations are necessary Service Precautions.