Removal
3UR-FE ENGINE MECHANICAL: ENGINE ASSEMBLY: REMOVAL
1. DISCHARGE FUEL SYSTEM PRESSURE Removal
2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
3. REMOVE NO. 1 ENGINE UNDER COVER Replacement
4. DRAIN ENGINE OIL Replacement
5. DRAIN ENGINE COOLANT Service and Repair
6. REMOVE HOOD SUB-ASSEMBLY
(a) Using a screwdriver, release the 2 clips and remove the hood support assembly.
HINT
Tape the screwdriver tip before use.
CAUTION:
Remove the hood support assembly while supporting the hood by hand.
(b) Remove the 4 bolts and hood.
7. REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY
(a) Remove the windshield wiper motor Removal.
8. REMOVE COWL TOP OUTER PANEL SUB-ASSEMBLY Removal
9. REMOVE V-BANK COVER SUB-ASSEMBLY
(a) Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
10. REMOVE AIR CLEANER HOSE ASSEMBLY
(a) Disconnect the vacuum hose and ventilation hose.
(b) Loosen the 2 clamps.
(c) Remove the air cleaner hose.
11. REMOVE AIR CLEANER ASSEMBLY
(a) Remove the air cleaner cap.
(1) Disconnect the MAF meter connector.
(2) Using a clip remover, detach the wire harness clamp.
(3) Unfasten the 4 hook clamps and then remove the air cleaner cap.
(b) Remove the air cleaner element.
(c) Remove the 2 bolts and air cleaner case.
12. REMOVE INLET RADIATOR HOSE
13. REMOVE OUTLET RADIATOR HOSE
14. REMOVE RADIATOR SIDE DEFLECTOR RH Removal
15. REMOVE RADIATOR SIDE DEFLECTOR LH Removal
16. REMOVE FAN & GENERATOR V BELT Removal
17. REMOVE FAN SHROUD Removal
18. REMOVE RADIATOR ASSEMBLY Removal
19. DISCONNECT FUEL MAIN AND RETURN HOSE
(a) Remove the fuel pipe clamp.
(b) Disconnect the fuel main and return hoses Service Precautions.
20. DISCONNECT WIRE HARNESS AND HOSE
(a) Disconnect the union to check valve hose.
(b) Disconnect the purge line hose.
(c) Disconnect the heater hoses.
(d) Disconnect the clamp and ECM connector.
HINT
Refer to the following procedures to disconnect the ECM connector Removal.
(e) Disconnect the 4 connectors from the connector holder block.
(f) Remove the nut and connector bracket and disconnect the 2 air pump connectors.
(g) Remove the bolt and disconnect the ground wire.
(h) Disconnect the 2 air injection system hoses.
(i) Remove the nut and disconnect the wire from the positive (+) battery cable.
(j) Disconnect the cable from the positive (+) battery terminal.
(k) Remove the bolt and disconnect the ground wire.
(l) Disconnect the 4 air injection control driver connectors.
(m) Remove the nut and disconnect the wire and 2 clips from the engine room junction block.
(n) Disconnect the 2 connectors and 2 clips from the engine room junction block.
21. DISCONNECT COOLER COMPRESSOR ASSEMBLY Removal
22. DISCONNECT VANE PUMP ASSEMBLY Removal
23. REMOVE GENERATOR ASSEMBLY Removal
24. REMOVE EXHAUST PIPE ASSEMBLY
(a) for Regular Cab Standard Deck:
Refer to the following procedures Removal.
(b) except Regular Cab Standard Deck:
Refer to the following procedures Removal.
25. REMOVE PROPELLER SHAFT ASSEMBLY
(a) for 2WD:
Refer to the following procedures Removal.
(b) for 4WD:
Refer to the following procedures Removal.
26. REMOVE FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
(a) Remove the front propeller shaft Removal.
27. REMOVE FRONT FENDER APRON SEAL RH Removal
28. REMOVE FRONT FENDER APRON SEAL REAR RH Removal
29. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE Removal
30. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR Removal
31. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH Removal
32. REMOVE STARTER COVER Removal
33. REMOVE STARTER ASSEMBLY Removal
34. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
(a) for 2WD:
Refer to the following procedures Removal.
(b) for 4WD:
Refer to the following procedures .
35. REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
(a) Using SST, hold the crankshaft.
SST : 09213-70011
SST : 09330-00021
(b) Remove the 10 bolts, rear drive plate spacer, drive plate and crankshaft angle sensor rotor.
36. REMOVE NO. 1 WATER BY-PASS PIPE
(a) Remove the 2 bolts and disconnect the hose. Then remove the water by-pass pipe.
37. REMOVE ENGINE ASSEMBLY
(a) Install the 2 engine hangers with the 2 bolts as shown in the illustration.
Torque : 43 Nm (438 kgf-cm, 32 ft-lbf)
HINT
(b) Attach an engine sling device and hang the engine with a chain block.
(c) Remove the 4 engine mounting insulator bolts.
(d) Lift the engine out from the vehicle slowly and carefully.
NOTICE:
Make sure the engine is clear of all wiring, hoses and cables.
38. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR Removal
39. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH Removal
40. INSTALL ENGINE ON ENGINE STAND
(a) Install the engine onto an engine stand with the bolts.
(b) Remove the 2 bolts and 2 engine hangers.