Component Location Overview
Component Location Overview
Components A through E are not shown in the exploded view illustration.
1 - Camshaft Adjustment Valve 1 (N205)
• Removing and installing, refer to => [ ] Service and Repair.
2 - Wastegate Bypass Regulator Valve (N75)
• Installed directly on the turbocharger. Refer to => [ Components on Turbocharger ].
3 - Turbocharger Recirculation Valve (N249)
• Installed directly on the turbocharger. Refer to => [ Components on Turbocharger ].
4 - Ignition Coil with Power Output Stage
• Removing and installing, refer to => [ Ignition Coils with Power Output Stages ] Service and Repair.
• Ignition coil 1 with power output stage (N70).
• Ignition coil 2 with power output stage (N127).
• Ignition coil 3 with power output stage (N291).
• Ignition coil 4 with power output stage (N292).
• The ignition coils must be pulled out of the cylinder head using ignition coil puller (T40039).
5 - Engine Control Module (ECM) (J623)
• Removing and installing, refer to the following:
• GTI and Eos, refer to => [ Engine Control Module, through 11.08 ] Service and Repair.
6 - High Pressure Pump with Fuel Pressure Regulator Valve (N276)
• Component location, refer to => [ High Pressure Pump ].
• Removing and installing, refer to => [ High Pressure Pump ] High Pressure Pump.
7 - Fuel Pressure Regulator Valve (N276)
• Component location, refer to => [ High Pressure Pump ].
8 - Engine Coolant Temperature (ECT) Sensor on Radiator (G83)
• Passat, CC, GTI and Eos: inside the lower radiator connection. Refer to => [ Radiator, Fan Shroud and Fans Overview ] Removal and Replacement.
9 - Vacuum Diaphragm for the Channel Separating Plate
• Component location, refer to => [ IMRC Valve ].
10 - Intake Manifold Runner Control (IMRC) Valve (N316)
• Component location, refer to => [ IMRC Valve ].
11 - Engine Speed Sensor (G28)
• Installed location: Left lower front, refer to => [ Engine Speed Sensor ].
12 - Charge Air Pressure Sensor (G31)
• Component location, refer to => [ Charge Air Pressure Sensor ].
13 - Knock Sensor 1 (G61) Electrical Connector
• Installed location: beneath the intake manifold => [ Electrical Connectors ].
• Knock sensor bolt tightening specification: 20 Nm.
14 - Camshaft Position (CMP) Sensor 2 (G40) Electrical Connector
• Installed location: beneath the intake manifold, refer to => [ Electrical Connectors ].
15 - 8-Pin Harness Connector for Fuel Injectors
• Installed location: beneath the intake manifold. Refer to => [ Electrical Connectors ].
16 - Throttle Valve Control Module (J338)
• With the Electronic Power Control (EPC) throttle drive (G186), EPC throttle drive angle sensor 1 (G187) and EPC throttle drive angle sensor 2 (G188).
• After replacing the throttle valve control module, it must be readapted to the ECM. Refer to the vehicle diagnostic tester.
17 - Evaporative Emission (EVAP) Canister Purge Regulator Valve 1 (N80)
18 - Intake Air Temperature (IAT) Sensor (G42)
• Bolted to the front of the intake manifold. Refer to => [ Intake Manifold Overview ] Intake Manifold Overview.
19 - Knock Sensor (KS) 1 (G61)
• On the front of the cylinder block under the intake manifold.
• Bolt tightening specification: 20 Nm
20 - Engine Coolant Temperature (ECT) Sensor (G62)
• In the coolant pump housing, refer to => [ ECT Sensor ].
21 - Camshaft Position (CMP) Sensor (G40)
• Bolted to the front of the cylinder head cover. Refer to => [ CMP Sensor ].
22 - Fuel Pressure Sensor (G247)
• On the fuel rail, refer to => [ Fuel Rail Overview ] Fuel Rail Overview.
23 - Intake Manifold Runner Position Sensor (G336)
• On the right side of the intake manifold.
• To remove and install, remove the intake manifold. Refer to => [ Intake Manifold with Fuel Rail ] Intake Manifold With Fuel Rail.
24 - Oil Pressure Switch (F1)
• Inside the accessory bracket. Refer to => [ Oil Filter, Cooler and Pressure Switch Overview ] Service and Repair.
A - Data Link Connector (DLC)
• In the driver's side footwell.
B - Mass Airflow (MAF) Sensor (G70) and Intake Air Temperature (IAT) Sensor 2 (G299)
• Component location, refer to => [ MAF Sensor and IAT Sensor 2 ].
• Removing and installing, refer to => [ ] Service and Repair.
C - Accelerator Pedal Position Sensor (G79) and Accelerator Pedal Position Sensor 2 (G185)
• On the accelerator pedal (both sensors are stored in one housing).
• If the accelerator pedal module or ECM is replaced in vehicles with automatic transmissions, the kick down function must be adapted.
• Removing and installing, refer to => [ Accelerator Pedal Module ] Accelerator Pedal Module.
D - Coolant Fan Control Module (J293)
• The coolant fan control module is integrated in the coolant fan (V7).
E - Fuel Injector
• In the fuel rail
• Removing and installing, refer to => [ Fuel Injectors ] Fuel Injectors.
• Cylinder 1 fuel injector (N30).
• Cylinder 2 fuel injector (N31).
• Cylinder 3 fuel injector (N32).
• Cylinder 4 fuel injector (N33).
High Pressure Pump
1 Fuel pressure regulator valve
2 Fuel high pressure pump
IMRC Valve
- IMRC valve - 2 -
- Vacuum diaphragm for the channel separating plate - 1 -.
MAF Sensor and IAT Sensor 2
- MAF sensor and IAT sensor 2- 1 -
Engine Speed Sensor
- Engine speed sensor - 1 -
CMP Sensor
- CMP sensor - 1 -
Electrical Connectors
1 CMP sensor connector
2 KS 1 connector
3 8-pin connector for the fuel injectors
ECT Sensor
- ECT sensor - 1 -
• Under the intake manifold (the intake manifold is not shown in the illustration).
Charge Air Pressure Sensor - 1 -
- Charge air pressure sensor - 1 -
Components on Turbocharger
1 Turbocharger, removing and installing. Refer to => [ Turbocharger ] Turbocharger.
2 Wastegate bypass regulator valve, tighten to 3 Nm.
3 Turbocharger recirculation valve, tighten to 7 Nm (observe the installed location, next illustration)
Installed Position of Turbocharger Recirculation Valve
