Front Seat Up-Down Motor Replacement
Front Seat Up-Down Motor Replacement
Front Up-down Motor - 8-Way Power Seat
SRS components are located in this area. Review the SRS component locations Locations and the precautions and procedures Service and Repair before doing repairs or service.
NOTE:
- Put on gloves to protect your hands.
- Take care not to tear or damage the seat covers.
1. Remove the front seat Front Seat Removal / Installation.
2. Remove the seat cushion cover/pad Front Seat Cushion Cover Replacement.
3. Remove the front up-down motor (A) and the front up-down motor bracket (B) as an assembly:
1. Disconnect the motor connector (C).
2. Remove the motor bracket mounting bolts (D) with a TORX T30 bit.
3. Remove the motor bracket mounting bolt (E) with a TORX T40 bit.
4. Detach the motor connector (A). Remove the bolts with a TORX T30 bit, then remove the front up-down motor (B) from the front up-down motor bracket (C).
5. Install the motor in the reverse order of removal, and note these items:
- Apply multipurpose grease to the pivot portions of the up-down adjuster and the motor pinion.
- When installing the front up-down motor (A), adjust the gear (B) to the motor pinion (C) by slightly rotating the brake (D) with an 8 mm hex wrench.
- Make sure the motor connector is plugged in properly.
- Check the front seat up-down operation.
Rear Up-down Motor - 8-Way Power Seat
SRS components are located in this area. Review the SRS component locations Locations and the precautions and procedures Service and Repair before doing repairs or service.
NOTE:
- Put on gloves to protect your hands.
- Take care not to tear or damage the seat covers.
Removal
1. Remove the front seat Front Seat Removal / Installation.
2. Remove these items:
- Seat-back cover/pad Service and Repair
- Seat cushion cover/pad Front Seat Cushion Cover Replacement
3. Remove the rear brake (A) and the rear brake bracket (B) as an assembly.
1. Remove the brake bracket mounting bolts (C) with a TORX T30 bit.
2. Remove the brake bracket mounting bolt (D) with a TORX T40 bit.
3. Pull back the brake bracket to remove the gear (E) from the brake gear axle.
4. Remove the gear (A).
5. Manually lower the seat frame down fully to access the rear bolt securing the rear up-down motor.
6. Disconnect and detach the motor connector (A). Remove the bolts with a TORX T30 bit, then remove the rear up-down motor (B).
7. Apply multipurpose grease to the pivot portions of the up-down adjuster.
Installation
8. Remove the bolts with a TORX T30 bit, then remove the rear brake (A) from the rear brake bracket (B).
9. Apply multipurpose grease to the motor pinion.
10. Install the rear up-down motor (A). Fasten the bolts with a TORX T30 bit. Connect the motor connector (B), and fasten the connector clip (C) to the seat frame. Make sure the connector is plugged in properly.
11. Manually raise the seat frame fully upward.
12. Install the gear (A) with its chamfered side faced the seat frame.
13. Install the rear brake bracket (A) without the rear brake to the seat frame. Lightly fasten all of the mounting bolts (B, C) with TORX T30 and T40 bits.
14. Carefully position the seat frame on its rear up-down motor side down.
15. Align the pinion (A) on the rear brake (B).
1. Engage the gear (C) with the motor pinion by hand, and center it.
2. Check the positions of the sector gear (D) and the cross-shaped hole (E) in the gear.
3. Align the pinion on the rear brake with the sector gear with an 8 mm hex wrench, and align the fingers (F) around the axle with the cross-shaped hole in the gear.
16. While holding the gear (A) perpendicular to the axle of the rear brake (B) by hand, install the rear brake on to the rear brake bracket (C).
NOTE:
- If you feel any interference between inside gears, remove the rear brake, and repeat step 15.
- If the rear brake seats fully on the rear brake bracket with no interference, go to step 17.
17. Install the rear brake mounting bolts (A), then tighten them to their specified torque with a TORX T30 bit. Install the rear brake bracket mounting bolts (B, C), then tighten them to their specified torque with TORX T30 and T40 bits.
18. Reinstall all of removed parts to the seat frame:
- Seat-back cover/pad Service and Repair
- Seat cushion cover/pad Front Seat Cushion Cover Replacement
19. Reinstall the front seat Front Seat Removal / Installation.
20. Check the front seat up-down operation.