Shift Cable and Selector Cable From Model Year 2008 Assembly Overview
Shift Cable and Selector Cable from Model Year 2008 Assembly Overview
• Grease bearing areas and slide surfaces with grease (G 000 450 02).
1 Transmission
2 Clip
• Not installed on all versions
• For selector relay lever from 8/2008
• Remove and secure
3 Transmission Shift Lever
• Inserting
• Installation location
• Adjust shift mechanism after installation, refer to => [ Shift Mechanism, Adjusting ] Adjustments
4 Control Cable Retainer
• For shift cable to transmission shift lever
• Allocation
• Disconnect from the shift cable
5 Retaining Washer
• Replace
• Removing
6 Nut
• Replace
• 23 Nm
• Self-locking
7 Retaining Clip
• Replace
8 Shift Cable
• Remove from the transmission shift lever and attach
• Removing and installing, refer to => [ Shift Cable and Selector Cable ] Service and Repair
• Adjusting, refer to => [ Shift Mechanism, Adjusting ] Adjustments
9 Selector Cable
• Removing and installing, refer to => [ Shift Cable and Selector Cable ] Service and Repair
• Adjusting, refer to => [ Shift Mechanism, Adjusting ] Adjustments
10 Shift Housing
11 Circlips
• Replace
12 Retaining Clip
• Replace
13 Control Cable Mounting Bracket
14 Bolt
• 20 Nm
• Quantity 3
15 Grommet
16 Bushing
17 Nut
• Only in vehicles with a 4-cylinder engine
18 Selector Relay Lever
• Made of plastic
• Different versions; allocation, refer to the electronic parts catalog ETKA
• Installation location
• Remove the selector relay lever with catch from the transmission shift lever and attach
• Remove the selector relay lever with clip from the transmission shift lever and attach
19 Slide Shoe
• Installation location
20 Control Cable Retainer
• For the selector cable on the selector relay lever
• Allocation => [ Allocation of Control Cable
Retainers ] Shift Cable and Selector Cable to Model Year 2007 Assembly Overview
• Disconnect from the selector cable
21 Lock Elbow
• For adjustment of shift mechanism, refer to => [ Shift Mechanism, Adjusting ] Adjustments
Allocation of Control Cable Retainers
The holes in the control cable retainers have various diameters.
Installing the Transmission Shift Lever
- When positioning the transmission shift lever, make sure the gap - arrow A - is placed over the missing selector shaft teeth - arrow B -.
Installation Position of Transmission Shift Lever/Selector Relay Lever
1 Transmission shift lever
2 Clip or catch (depending on the version)
3 The selector relay lever engages in the transmission shift lever slide rail via the slide shoe - arrow B -.
- Lubricate the slide rail and slide shoe - arrow - with grease (G 000 450 02).
Disconnect the Control Cable Retainer from the Shift Cable and Selector Cable
- Pull the securing mechanism forward to the stop - arrow 1 - and then lock to the left - arrow 2 -.
- Remove control cable - B - from control cable retainer - A -.
Remove the Shift Cable from the Transmission Shift Lever and Attach
Removal
- Remove shift cable lock washer - 3 - from transmission shift lever - 1 - by lifting the clip.
- Remove shift cable - 2 - from the pin - arrow -.
Securing
• Replace the lock washer for the shift cable.
• Coat the pin - arrow - with a small amount of grease (G 000 450 02).
- Press the shift cable onto transmission shift lever - 2 - and secure with lock washer - 1 -.
Remove the Selector Relay Lever with Catch from the Transmission Shift Lever - arrow 1 - and Attach
Removal
- Press in the catch - arrow 1 - to the stop and remove the selector relay lever together with the control cable retainer. Move the selector relay lever in the operating direction.
• Ignore - arrow 2 -.
Securing
• To install, grease mounting points and contact surfaces with Grease (G 000 450 02).
- Press the control cable retainer onto the selector relay lever
- Insert the selector relay lever together with the control cable retainer to the stop.
• The catch - arrow 1 - secures the selector relay lever.
• The catch - arrow 2 - secures the control cable retainer.
• Make sure it engages securely.
Remove the Selector Relay Lever "with Clip" from the Transmission Shift Lever - arrow 1 - and Attach
Removal
- Remove the clip - arrow 1 -, and remove the selector relay lever together with the control cable retainer.
Securing
• Grease bearing areas and slide surfaces with grease (G 000 450 02).
- Insert the selector relay lever together with the control cable retainer to the stop.
- Press on the clip - arrow 1 - while ensuring that it engages securely.
• Ignore - arrow 2 -.
Pry the Selector Cable Retainer Out of the Selector Relay Lever
• Selector relay lever removed.
- Apply a flat head screwdriver - A - between bushing - B - and the selector relay lever.
Press the Selector Cable Retainer onto the Selector Relay Lever
• Selector relay lever removed.
• The cable retainer may only be pressed on at the bushing - arrow -.
• The control cable retainer must move freely on the selector relay lever.
• The control cable retainer must be behind the catch.
- Make sure it engages securely.