B2545

DTC B2545

Diagnostic Instructions

* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using this diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.

DTC Descriptor
DTC B2545 00
- Backup Lamps Circuit

Diagnostic Fault Information





Circuit/System Description

When the transmission is placed in the REVERSE position, the transmission control module (TCM) sends a serial data message to the body control module (BCM). The message indicates that the gear selector is in the REVERSE position. The BCM applies battery voltage to the backup lamps and inside rearview mirror. Once the driver moves the gear selector out of the REVERSE position, a message is sent by the TCM via serial data requesting the BCM to remove battery voltage from the backup lamp control circuit. The engine may need to be running for the backup lamps to function.

Conditions for Running the DTC

Battery voltage must be between 9-16 V.

Conditions for Setting the DTC

DTC B2545 00 will set when one of the following conditions exists:

* The BCM detects a short to ground in the backup lamps control circuit.
* The BCM detects a short to ground or an open/high resistance in the BCM 4 fuse B+ circuit.

Actions Taken When the DTC Sets

The backup lamps will not operate.

Conditions for Clearing the DTC

* The condition responsible for setting the DTC no longer exists.
* A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred.

Reference Information
Schematic Reference

Exterior Lights Schematics (Exterior Lights Schematics)
Connector End View Reference

Component Connector End Views (Connector Views)
Description and Operation

Exterior Lighting Systems Description and Operation (Exterior Lighting Systems Description and Operation)
Electrical Information Reference

* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing for Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)

Scan Tool Reference

Control Module References (Programming and Relearning) for scan tool information

Circuit/System Testing

1. Ignition OFF, disconnect the harness connector at the inside rearview mirror.
2. Connect a test lamp between the control circuit terminal 9 and ground.
3. Command the Backup Lamps ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

• If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM.
• If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, test the BCM 4 fuse B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.

4. Connect the harness connector at the inside rearview mirror.
5. Ignition OFF, disconnect the harness connector at the appropriate tail lamp.
6. Ignition OFF, exterior lamps OFF, test for less than 5.0 ohm between the ground circuit terminal C and ground.

• If greater than the specified range, test the ground circuit for an open/high resistance.

7. Connect a test lamp between the control circuit terminal E and ground.
8. Command the Backup Lamps ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

• If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM.
• If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.

9. If all circuits test normal, replace the tail lamp.

Repair Instructions

Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.

* Tail Lamp Replacement (Sedan, V-Series) (Service and Repair)Tail Lamp Replacement (Wagon) (Service and Repair)
* Inside Rearview Mirror Replacement (Inside Rearview Mirror Replacement)
* Control Module References (Programming and Relearning) for BCM replacement, setup, and programming