B3265
DTC B3265
Diagnostic Instructions
* Perform the Diagnostic System Check - Vehicle (Diagnostic System Check - Vehicle) prior to using the diagnostic procedure.
* Review Strategy Based Diagnosis (Strategy Based Diagnosis) for an overview of the diagnostic approach.
* Diagnostic Procedure Instructions (Diagnostic Procedure Instructions) provides an overview of each diagnostic category.
DTC Descriptor
DTC B3265 00
- Trunk Release Output Circuit
Diagnostic Fault Information
Circuit/System Description
When the ignition is ON, the body control module (BCM) supplies battery positive voltage to the rear compartment lid release switch through the trunk release switch supply voltage circuit. When the rear compartment lid release switch is operated, the trunk release supply voltage circuit is grounded through the switch ground circuit and the voltage is pulled low within the BCM. In response, the BCM applies battery positive voltage to the trunk release relay control circuit, which energizes the coil side of the trunk relay. The switch side of the trunk relay then closes, supplying battery positive voltage through the relay and the latch motor voltage control circuit to the rear compartment lid latch. The rear compartment lid latch then releases the rear compartment lid so that it may be manually raised to an open position.
Conditions for Running the DTC
Battery voltage must be between 9-16 volts.
Conditions for Setting the DTC
When the BCM detects a fault in the trunk relay control circuit.
Action Taken When the DTC Sets
The rear compartment lid latch will malfunction.
Conditions for Clearing the DTC
* The DTC will be current for as long as the fault is present.
* When the fault is no longer present, the DTC will be a history DTC.
* A history DTC will clear after 50 ignition cycles
Reference Information
Schematic Reference
Release Systems Schematics (Release Systems Schematics)
Connector End View Reference
Component Connector End Views (Connector Views)
Description and Operation
Luggage Compartment Description and Operation (Description and Operation)
Electrical Information Reference
* Circuit Testing (Circuit Testing)
* Connector Repairs (Connector Repairs)
* Testing for Intermittent Conditions and Poor Connections (Testing For Intermittent Conditions and Poor Connections)
* Wiring Repairs (Wiring Repairs)
Scan Tool Reference
Control Module References (Programming and Relearning) for scan tool information
Circuit/System Verification
Ignition ON, command the Trunk Release with a scan tool. The rear compartment lid latch should release the trunk lid.
Circuit/System Testing
1. Ignition OFF, disconnect the TRK REL relay.
2. Test for less than 1 ohm between the ground circuit terminal 85 and ground.
• If greater than the specified range, test the ground circuit for an open/high resistance.
3. Connect a test lamp between the control circuit terminal 86 and the ground circuit terminal 85.
4. Ignition ON, command the Trunk Release with a scan tool. The test lamp should illuminate during the RELEASE command.
• If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM.
• If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
5. If all circuits test normal, test or replace the TRK REL relay.
Component Testing
Relay Test
1. Ignition OFF, disconnect the TRK REL relay.
2. Test for 60-180 ohms between terminals 85 and 86.
• If not within the specified range, replace the relay.
3. Test for infinite resistance between the following terminals:
* 30 and 86
* 30 and 87
* 30 and 85
* 85 and 87
• If not the specified value, replace the relay.
4. Install a 25A fused jumper wire between relay terminal 85 and 12 volts. Install a jumper wire between relay terminal 86 and ground. Test for less than 2 ohms between terminals 30 and 87.
• If greater than the specified range, replace the relay.
Repair Instructions
Perform the Diagnostic Repair Verification (Verification Tests) after completing the diagnostic procedure.
* Relay Replacement (Attached to Wire Harness) (Relay Replacement (Attached to Wire Harness))Relay Replacement (Within an Electrical Center) (Relay Replacement (Within an Electrical Center))
* Control Module References (Programming and Relearning) for BCM replacement, setup, and programming