For Mexico
P0340, P0345 CMP SENSOR
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1. PRECONDITIONING
1.Turn ignition switch OFF and wait at least 10 seconds.
2.Turn ignition switch ON.
3.Turn ignition switch OFF and wait at least 10 seconds.
- GO TO 2.
2. PERFORM DTC CONFIRMATION PROCEDURE-I
1.Start engine and let it idle for at least 5 seconds.
If engine does not start, crank engine for at least 2 seconds.
2.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Go to "Diagnosis Procedure" .
NO- GO TO 3.
3. PERFORM DTC CONFIRMATION PROCEDURE-I
1.Maintain engine speed at more than 800 rpm for at least 5 seconds.
2.Check 1st trip DTC.
Is 1st trip DTC detected?
YES- Go to "Diagnosis Procedure" .
NO- INSPECTION END
Diagnosis Procedure
1. CHECK STARTING SYSTEM
Turn ignition switch to START position.
Does the engine turn over? Does the starter motor operate?
YES- GO TO 2.
NO- Check starting system. (Refer to "Work Flow (With GR8-1200 NI)" Work Flow (With GR8-1200 NI), or "Work Flow (Without GR8-1200 NI)" Work Flow (Without GR8-1200 NI). For the details of the GR8-1200 NI,
2. CHECK CAMSHAFT POSITION SENSOR POWER SUPPLY CIRCUIT-I
1.Disconnect camshaft position (CMP) sensor harness connector.
2.Turn ignition switch ON.
3.Check the voltage between CMP sensor harness connector and ground.
Is the inspection result normal?
YES- GO TO 8.
NO-1- P0340: GO TO 3.
NO-2- P0345: Repair open circuit, short to ground or short to power in harness or connectors.
3. CHECK CMP SENSOR POWER SUPPLY CIRCUIT-II
1.Turn ignition switch OFF.
2.Disconnect ECM harness connector.
3.Check the continuity between CMP sensor harness connector and ECM harness connector.
Is the inspection result normal?
YES- GO TO 4.
NO- Repair open circuit.
4. CHECK SENSOR POWER SUPPLY CIRCUIT
Check harness for short to power and short to ground, between the following terminals.
Is the inspection result normal?
YES- GO TO 5.
NO- Repair short to ground or short to power in harness or connectors.
5. CHECK COMPONENTS
Check the following.
- Battery current sensor (Refer to "Component Inspection (Battery Current Sensor)" For Mexico.)
- Crankshaft position sensor (Refer to "Component Inspection (Crankshaft Position Sensor)" For Mexico.)
- Refrigerant pressure sensor (Refer to "Component Function Check" For Mexico.)
- EVAP control system pressure sensor (Refer to "Component Inspection (EVAP Control System Pressure Sensor)" For Mexico.)
Is the inspection result normal?
YES- GO TO 6.
NO- Replace malfunctioning component.
6. CHECK APP SENSOR
Refer to "Component Inspection (Accelerator Pedal Position Sensor)" For Mexico.
Is the inspection result normal?
YES- GO TO 12.
NO- GO TO 7.
7. REPLACE ACCELERATOR PEDAL ASSEMBLY
Replace accelerator pedal assembly. Refer to "MODELS WITHOUT DISTANCE CONTROL ASSIST SYSTEM : Removal and Installation" Without Distance Control Assist System (Without distance control assist system)
8. CHECK CMP SENSOR GROUND CIRCUIT FOR OPEN AND SHORT
1.Turn ignition switch OFF.
2.Disconnect ECM harness connector.
3.Check the continuity between CMP sensor harness connector and ECM harness connector.
4.Also check harness for short to ground and short to power.
Is the inspection result normal?
YES- GO TO 9.
NO- Repair open circuit, short to ground or short to power in harness or connectors.
9. CHECK CMP SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1.Check the continuity between CMP sensor harness connector and ECM harness connector.
2.Also check harness for short to ground and short to power.
Is the inspection result normal?
YES- GO TO 10.
NO- Repair open circuit, short to ground or short to power in harness or connectors.
10. CHECK CAMSHAFT POSITION SENSOR
Refer to "Component Inspection (Camshaft Position Sensor)" .
Is the inspection result normal?
YES- GO TO 11
NO- Replace malfunctioning camshaft position sensor. Refer to "Exploded View" Exploded View.
11. CHECK CAMSHAFT (INT)
Check the following.
- Accumulation of debris to the signal plate of camshaft front end
- Chipping signal plate of camshaft front end
Is the inspection result normal?
YES- GO TO 12.
NO- Remove debris and clean the signal plate of camshaft front end or replace camshaft.
12. CHECK INTERMITTENT INCIDENT
Refer to "Intermittent Incident" Intermittent Incident.
- INSPECTION END
Component Inspection (Camshaft Position Sensor)
1. CHECK CAMSHAFT POSITION SENSOR-I
1.Turn ignition switch OFF.
2.Loosen the fixing bolt of the sensor.
3.Disconnect camshaft position sensor harness connector.
4.Remove the sensor.
5.Visually check the sensor for chipping.
Is the inspection result normal?
YES- GO TO 2.
NO- Replace malfunctioning camshaft position sensor.
2. CHECK CAMSHAFT POSITION SENSOR-II
Check resistance camshaft position sensor terminals as per the following.
Is the inspection result normal?
YES- INSPECTION END
NO- Replace malfunctioning camshaft position sensor. Refer to "Exploded View" Exploded View.