Installation

INTERIOR: ROOF HEADLINING:

INSTALLATION

1. INSTALL ROOF WIRE AND RADIO ANTENNA CORD
(a) Attach the roof wire, radio antenna cord and washer hose along the adhesive part.

NOTE: Attach the roof wire, radio antenna cord and washer hose securely.
HINT: Be careful that dirt or foreign objects do not stick to the adhesive part when removing the peeling paper.

2. INSTALL ROOF HEADLINING ASSEMBLY
(a) Place the roof headlining to the vehicle from the back door side.
(b) Engage the 2 fasteners and 3 clips. (w/o sliding roof)

(c) Engage the 3 clips. (w/ sliding roof)
(d) Install the sunroof opening trim moulding. (w/ sliding roof)
(e) Connect the sliding roof drive gear connector. (w/ sliding roof)
(f) Connect the washer hose. Connect the radio antenna cord connector and engage the clamps to the rear quarter pillar RH.
(g) Connect the roof wire connector and engage the clamps to the front pillar LH.
(h) Connect the washer hose. Connect the radio antenna cord connector and engage the clamps to the front pillar RH.
(i) Install the radio antenna cord connector bolt to the front pillar RH.
3. INSTALL VISOR HOLDER
4. INSTALL LH VISOR ASSEMBLY
(a) Connect the connector.
(b) Install the visor assembly with the 2 screws.
(c) Engage the 4 claws and install the visor bracket cover.
5. INSTALL RH VISOR ASSEMBLY
6. INSTALL MAP LIGHT ASSEMBLY

(a) Connect the connector.
(b) Install the map light with the 4 screws.

(d) w/o sliding roof:
Engage the 6 claws and install the lens cover.

(e) w/ sliding roof:
Engage the 8 claws and install the lens cover.
7. INSTALL ROOM LIGHT ASSEMBLY NO.1
(a) Connect the connector.
(b) Engage the 2 claws and 2 springs, and install the room light assembly No.1.

(c) Engage the 4 claws and install the lens cover.
8. INSTALL RAIN SENSOR (W/ RAIN SENSOR) Installation

9. INSTALL ASSIST GRIP SUB-ASSEMBLY
(a) Install the assist grip sub-assembly with the 2 screws.

(b) Engage the 6 claws and install the 2 assist grip covers.
HINT: Use the same procedure for the other 3 assist grips.

10. INSTALL TELEVISION DISPLAY ASSEMBLY (W/ TELEVISION DISPLAY) Installation

11. INSTALL TELEVISION BASE (W/ TELEVISION DISPLAY) Installation

12. INSTALL ROOF SIDE LH GARNISH ASSEMBLY INNER

(a) Engage the 7 clips and install the roof side garnish assembly inner.

(b) Install the 3 clips.
(c) Install the 3 bolts and tonneau cover holder cap.

(d) Engage the 4 claws and install the seat belt bezel.
13. INSTALL ROOF SIDE RH GARNISH ASSEMBLY INNER
14. INSTALL ROOM LIGHT ASSEMBLY NO.2

(a) Connect the connector.
(b) Engage the claw and install the room light assembly No.2.
15. INSTALL DECK TRIM SIDE LH PANEL ASSEMBLY

(a) Engage the 2 clips and install the deck trim side panel assembly.
(b) Install the 4 clips.
16. INSTALL DECK TRIM SIDE RH PANEL ASSEMBLY
17. INSTALL ROPE HOOK
(a) Install the 2 rope hooks with the 2 bolts.
Torque: 8.0 Nm (80 kgf-cm, 71 in-lbf)
HINT: Use the same procedure to install the other side.

18. INSTALL REAR FLOOR FINISH SIDE LH PLATE

(a) Engage the 2 clips and install the rear floor finish side plate.
(b) Install the clip.
19. INSTALL REAR FLOOR FINISH SIDE RH PLATE
20. INSTALL REAR SEAT SIDE LH COVER

(a) Engage the 4 clips and install the rear seat side cover.
(b) Install the 3 clips.
21. INSTALL REAR SEAT SIDE RH COVER
22. INSTALL REAR NO.1 SEAT OUTER LH BELT ASSEMBLY
(a) Install the rear No.1 seat outer belt assembly with the bolt.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)
23. INSTALL REAR NO.1 SEAT OUTER RH BELT ASSEMBLY
24. INSTALL DECK SIDE TRIM LH COVER

(a) Engage the 5 claws and install the deck side trim cover.
25. INSTALL DECK SIDE TRIM RH COVER
26. INSTALL CENTER PILLAR LH GARNISH

(a) Engage the clip and install the center pillar garnish.
(b) Install the 2 screws.
27. INSTALL CENTER PILLAR RH GARNISH
28. INSTALL CENTER PILLAR LH GARNISH LOWER

(a) Engage the 2 clips and 3 claws, install the center pillar garnish lower.
29. INSTALL CENTER PILLAR RH GARNISH LOWER
30. INSTALL FRONT SEAT OUTER LH BELT ASSEMBLY

(a) Install the front seat outer belt assembly with the bolt.
Torque: 42 Nm (428 kgf-cm, 31 ft-lbf)
31. INSTALL FRONT SEAT OUTER RH BELT ASSEMBLY
32. INSTALL LAP BELT OUTER ANCHOR COVER

(a) Engage the 2 claws and install the lap belt outer anchor cover as shown in the illustration.
HINT: Use the same procedure to install the other side.

33. INSTALL FRONT PILLAR LH GARNISH

(a) Install a new clip (A) on the front pillar garnish.
(b) Engage the 2 claws and 2 clips, and install the front pillar garnish.
34. INSTALL FRONT PILLAR RH GARNISH
35. INSTALL REAR DOOR OPENING TRIM LH WEATHERSTRIP
36. INSTALL REAR DOOR OPENING TRIM RH WEATHERSTRIP
37. INSTALL REAR DOOR SCUFF LH PLATE

(a) Connect the connector. (w/ illumination scuff plate)
(b) Engage the 4 claws and 2 clips, and install the rear door scuff plate.
38. INSTALL REAR DOOR SCUFF RH PLATE
39. INSTALL FRONT DOOR OPENING TRIM LH WEATHERSTRIP
40. INSTALL FRONT DOOR OPENING TRIM RH WEATHERSTRIP
41. INSTALL FRONT DOOR SCUFF LH PLATE

(a) Connect the connector. (w/ illumination scuff plate)
(b) Engage the 6 claws and 4 clips, and install the front door scuff plate.
42. INSTALL FRONT DOOR SCUFF RH PLATE
43. INSTALL REAR SEAT ASSEMBLY RH Installation

44. INSTALL REAR SEAT TRACK BRACKET COVER
45. INSTALL REAR SEAT ASSEMBLY LH Installation

46. INSTALL REAR SEAT TRACK BRACKET COVER
47. INSTALL DECK SIDE TRIM LH BOX

(a) Install the deck side trim box with the 2 clips.
48. INSTALL DECK SIDE TRIM RH BOX
49. INSTALL JACK CARRIER ASSEMBLY
(a) Install the jack carrier assembly, jack assembly and jack carrier support.
50. INSTALL REAR FLOOR FINISH PLATE

(a) Engage the 2 claws and 6 clips, and install the rear floor finish plate.
(b) Install the 2 clips.
51. INSTALL BACK DOOR WEATHERSTRIP
52. INSTALL DECK NO.3 BOARD SUB-ASSEMBLY

(a) Install the deck No.3 board sub-assembly with the 2 bolts and 2 nuts.
53. INSTALL DECK NO.2 BOARD SUB-ASSEMBLY

(a) Install the deck No.2 board sub-assembly with the 4 bolts and 2 nuts.
54. INSTALL DECK FLOOR BOX REAR

(a) Install the deck floor box rear with the 2 clips.
55. INSTALL DECK FLOOR BOX FRONT

(a) Install the deck floor box front with the 2 clips.
56. INSTALL DECK BOARD SUB-ASSEMBLY

(a) Install the deck board sub-assembly with the 2 bolt.
(b) Engage the 5 clips.
57. INSTALL TONNEAU COVER ASSEMBLY
58. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
59. PERFORM INITIALIZATION Repair Instruction - Initialization

60. INSPECT SLIDE ADJUSTER LOCK Installation