Removal

A760F AUTOMATIC TRANSMISSION / TRANSAXLE: AUTOMATIC TRANSMISSION ASSEMBLY: REMOVAL

1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
* w/ Navigation System (for HDD): After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.

Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal:





* When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

2. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY Removal

3. REMOVE REAR ENGINE UNDER COVER ASSEMBLY Removal

4. REMOVE PROPELLER SHAFT HEAT INSULATOR

(a) Remove the 2 bolts and propeller shaft heat insulator.





5. DRAIN AUTOMATIC TRANSMISSION FLUID Removal

6. DRAIN ENGINE COOLANT Service and Repair

7. REMOVE FRONT PROPELLER SHAFT ASSEMBLY

(a) Remove the front propeller shaft Removal.

8. REMOVE PROPELLER SHAFT ASSEMBLY

(a) Remove the propeller shaft Removal.

9. REMOVE FRONT EXHAUST PIPE ASSEMBLY

(a) Remove the front exhaust pipe Removal.

10. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY





(a) Remove the nut and clip and disconnect the transmission control cable from the transmission.

11. REMOVE STARTER ASSEMBLY

(a) Remove the starter Removal.

12. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT





(a) Remove the flywheel housing side cover.

(b) Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.





13. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY





(a) Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.

14. REMOVE FRONT SUSPENSION MEMBER BRACKET LH AND RH

(a) Remove the 8 bolts and front suspension member bracket LH and RH.





15. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY





(a) Remove the 4 bolts of the rear engine mounting insulator.

(b) Remove the 4 nuts, 4 bolts and frame crossmember.





16. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

(a) Remove the bolt and rear engine mounting heat insulator.





(b) Remove the 4 bolts and rear engine mounting insulator from the transmission.

17. DISCONNECT WIRE HARNESS AND CONNECTOR





(a) Remove the nut and disconnect the ground cable.

(b) Tilt the transmission downward.





NOTICE:
Make sure the cooling fan does not contact the fan shroud.

(c) Remove the 2 nuts and No. 2 wire harness heat insulator.





Text in Illustration





(d) Remove the nut and disconnect the crankshaft position sensor connector and sensor harness.

(e) Disconnect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and transfer control connector.

HINT
Detach the claw, press down the lever, and then disconnect the transmission wire connector.

(f) Detach the 2 connector clamps and 8 harness clamps and disconnect the wire harness.

18. DISCONNECT NO. 1 WATER BY-PASS PIPE

(a) Disconnect the 2 water by-pass hoses from the transmission oil cooler.





NOTICE:
Use a container to catch any coolant which flows out of the water by-pass hoses.

(b) Remove the 2 bolts and disconnect the water by-pass pipe.

19. REMOVE TRANSMISSION OIL COOLER ASSEMBLY

(a) Disconnect the No. 2 oil cooler inlet hose and No. 2 oil cooler outlet hose from the transmission oil thermostat.





(b) Disconnect the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose from each oil cooler tube union.





(c) Remove the 3 bolts and transmission oil cooler with transmission oil thermostat.

20. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY





(a) Remove the 10 bolts and transmission.

NOTICE:
Do not use excess force when prying the transmission assembly.

21. REMOVE HARNESS CLAMP BRACKET

(a) Remove the 7 bolts and 7 brackets.

22. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET





(a) Remove the 2 bolts and bracket.

23. REMOVE TRANSFER ASSEMBLY

(a) Remove the transfer Removal.

24. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY

25. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY

(a) Inspect the torque converter clutch Testing and Inspection.