Installation
ENGINE HOOD / DOOR: LUGGAGE DOOR HINGE TORSION BAR: INSTALLATION
INSTALLATION
HINT:
- The installation should be performed in the order of LH to RH.
- After installing the torsion bar, use your hand to open and close the luggage door. Make sure the luggage door can open and close smoothly.
1. INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR TORSION BAR SUPPORT
(a) Squeeze the two sides of the torsion bar support indicated by the arrows and install it as shown in the illustration.
2. INSTALL LUGGAGE DOOR HINGE TORSION BAR LH
(a) Using SST, install the luggage door hinge torsion bar LH to the luggage door hinge and body LH side
SST: 09804-24010
(b) Set the tip of the luggage door hinge torsion bar LH in the installation hole in the center. The upper and lower holes are used for adjustment.
(c) Connect the luggage door hinge torsion bar LH to the body RH side.
(d) Connect the luggage door hinge torsion bar LH to the luggage compartment door torsion bar support.
3. INSTALL LUGGAGE DOOR HINGE TORSION BAR RH
(a) Using SST, install the luggage door hinge torsion bar RH to the luggage door hinge and body RH side.
SST: 09804-24010
(b) Set the tip of the luggage door hinge torsion bar RH in the installation hole in the center. The upper and lower holes are used for adjustment.
(c) Connect the luggage door hinge torsion bar RH to the body LH side.
(d) Connect the luggage door hinge torsion bar RH to the luggage compartment door torsion bar support.
(e) Attach the 3 clips and install the luggage door wire.
4. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY RH
(a) Install the trim cover with the claw and 2 clips.
5. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH
(a) Install the trim cover with the claw and 2 clips.
6. INSTALL REAR FLOOR FINISH PLATE
(a) Attach the 4 clips to install the rear floor finish plate.
(b) Install the 3 clips.
7. INSTALL TOOL BOX (w/o Spare Tire) Installation
8. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)
9. INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER
(a) w/o Rear Cooler:
(1) Install the trim cover with the 4 claws and 3 clips.
(b) w/ Rear Cooler:
(1) Install the trim cover with the 4 claws and 5 clips.
10. INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
(a) Connect the connector.
(b) Attach the 2 claws to install the courtesy light.
11. INSTALL NO. 1 COOLER COVER (w/ Rear Cooler) Installation
12. INSTALL DECK TRIM SIDE BOARD RH
(a) w/ Spare Tire:
(1) Install the deck trim side board with the clip.
(b) w/o Spare Tire:
(1) Attach the clip to install the deck trim side board.
13. INSTALL ROPE HOOK ASSEMBLY
(a) Install the 4 rope hooks with the 4 bolts.
14. INSTALL ROPE HOOK
(a) Install the 4 rope hooks.
15. INSTALL BATTERY SERVICE HOLE COVER
(a) Slide the battery service hole cover in the direction of arrow 1 to attach the claw. Then push the cover in the direction of the arrow 2 to install it.
16. INSTALL BATTERY SERVICE HOLE COVER LH
(a) Attach the battery service hole cover LH with the clip and fastening tape.
17. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)
(a) Attach the 2 clips to install the deck trim side board LH.
18. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY
19. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER LH
(a) Install the door hinge cover with the 3 clips.
20. INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER RH
(a) Install the door hinge cover with the 3 clips.