Installation

2UR-FSE COOLING: RADIATOR: INSTALLATION

INSTALLATION

1. INSTALL RADIATOR SUPPORT LOWER
(a) Install the 2 supports.
2. INSTALL RADIATOR SUPPORT CUSHION
(a) Install the 2 cushions.
3. INSTALL FAN SHROUD WITH FAN AND MOTOR





(a) Set the fan shroud with fan and motor to the radiator, and attach the claw.
(b) Install the fan shroud with the 2 bolts.
Torque: 5.0 Nm (51 kgf-cm, 44in-lbf)
4. INSTALL RADIATOR ASSEMBLY





(a) Install the A/C condenser with HV radiator to the radiator with the 4 bolts.
Torque: 5.0 Nm (51 kgf-cm, 44in-lbf)





(b) Install the radiator to the front crossmember.
HINT: Install the radiator to the front side holes of the radiator's lower support.

5. CONNECT LIQUID TUBE SUB-ASSEMBLY A Installation
6. CONNECT DISCHARGE HOSE SUB-ASSEMBLY Installation
7. CONNECT NO. 7 INVERTER COOLING HOSE





(a) Connect the cooling hose.
8. CONNECT NO. 2 INVERTER COOLING HOSE





(a) Connect the cooling hose.
9. INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY





(a) Attach the wire harness to the upper support with the 5 clamps.





(b) Install the upper support with the 5 bolts.
Torque: 8.0 Nm (82 kgf-cm, 71in-lbf)





(c) Attach the 2 clamps to the radiator support LH and RH side.
(d) Connect the 3 connectors.
10. INSTALL HOOD LOCK ASSEMBLY Installation
11. INSTALL HOOD LOCK CONTROL CABLE COVER





(a) Attach the claw to install the cover.
(b) Install the 3 screws.
12. INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)





(a) Install the sensor with the 3 bolts.
Torque: 5.5 Nm (56 kgf-cm, 49in-lbf)
(b) Connect the connector.
13. CONNECT WIRE HARNESS





(a) Attach the 5 clamps and connect the 2 connectors.





(b) Attach the 3 clamps and connect the ECU connector.
14. INSTALL OUTLET ENGINE ROOM ECU DUCT Installation
15. CONNECT OUTLET OIL COOLER HOSE





(a) Connect the hose to the radiator.
- The direction of the hose clamp is indicated in the illustration.
- Insert the cooler hose into the stopper. Set the hose clamp so that the clearance between the hose clamp and stopper is within 2 to 7 mm (0.0787 to 0.276 in.).

16. CONNECT INLET OIL COOLER HOSE
(a) Connect the hose to the radiator.
HINT:
- The direction of the hose clamp is indicated in the illustration.
- Insert the cooler hose into the stopper. Set the hose clamp so that the clearance between the hose clamp and stopper is within 2 to 7 mm (0.0787 to 0.276 in.).

17. INSTALL NO. 2 RADIATOR HOSE





(a) Install the radiator hose.
HINT: The direction of the hose clamp is indicated in the illustration.





18. INSTALL NO. 1 RADIATOR HOSE
(a) Connect the No. 1 radiator hose to the radiator and water outlet, and then secure it with the hose clamps.
NOTICE:
If the vehicle is equipped with a water hose set on the water outlet side, assemble the water hose set before use.
- The direction of the hose clamp is indicated in the illustration.
- Insert the radiator hose into the stopper. Set the hose clamp so that the clearance between the hose clamp and the stopper is within 1.0 to 5.0 mm (0.039 to 0.20 in.).

19. INSTALL RADIATOR RESERVOIR ASSEMBLY Installation
20. INSTALL FRONT BUMPER REINFORCEMENT Installation
21. INSTALL FRONT BUMPER ENERGY ABSORBER Installation
22. INSTALL FRONT BUMPER COVER Installation
23. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH Installation
24. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH Installation
25. INSTALL FRONT FENDER WHEEL OPENING MOULDING LH
26. INSTALL FRONT FENDER WHEEL OPENING MOULDING RH Installation
27. CHARGE REFRIGERANT Service and Repair
28. INSPECT AND ADJUST TRANSMISSION FLUID
(a) Inspect and adjust the transmission fluid level Procedures.
29. ADD COOLANT (for Inverter) Service and Repair
30. INSPECT FOR COOLANT LEAK (for Inverter) Testing and Inspection
31. ADD ENGINE COOLANT Service and Repair
32. INSPECT FOR COOLANT LEAK Testing and Inspection
33. INSPECT FOR REFRIGERANT LEAK Service and Repair
34. INSTALL COOL AIR INTAKE DUCT SEAL
(a) Install the duct seal with the 4 clips.
35. ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System) Adjustments
36. INSTALL RADIATOR GRILLE ASSEMBLY Installation
37. INSTALL NO. 1 ENGINE UNDER COVER Installation
38. INSTALL NO. 1 AIR CLEANER INLET Installation
39. INSTALL ENGINE ROOM SIDE COVER RH Installation
40. INSTALL ENGINE ROOM SIDE COVER LH Installation
41. INSTALL AIR CLEANER INLET COVER SUB-ASSEMBLY Installation
42. INSTALL V-BANK COVER SUB-ASSEMBLY Installation