Operation CHARM: Car repair manuals for everyone.

Installation





INTERIOR: ROOF HEADLINING: INSTALLATION

1. INSTALL NO. 1 ROOF WIRE (for Standard)

(a) Apply new double-sided tape to the locations shown in the illustration while aligning the tape with the markings on the roof headlining.





NOTICE:
Securely apply the double-sided tape to prevent the tape from being out of alignment and peeling off.

(b) Peel off the release paper from the double-sided tape.

(c) Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.

NOTICE:
* Securely attach the No. 1 roof wire.
* Failure to do so may cause abnormal noise.

(d) Turn the visor connectors clockwise approximately 90° to connect the connectors of the roof headlining.

(e) Apply adhesive tape to the locations shown in the illustration.





HINT
As shown at point A in the illustration, line up and secure the reference tape of the wire harness to the tip of the roof headlining assembly.

2. INSTALL NO. 1 ROOF WIRE (for Glass Roof)

(a) Apply new double-sided tape to the locations shown in the illustration while aligning the tape with the markings on the roof headlining.





NOTICE:
Securely apply the double-sided tape to prevent the tape from being out of alignment and peeling off.

(b) Peel off the release paper from the double-sided tape.

(c) Attach the No. 1 roof wire along the double-sided tape so that the marking surface of the wire harness faces downward.

NOTICE:
* Securely attach the No. 1 roof wire.
* Failure to do so may cause abnormal noise.

(d) Turn the visor connectors clockwise approximately 90° to connect the connectors of the roof headlining.

(e) Apply adhesive tape to the locations shown in the illustration.





HINT
As shown at point A in the illustration, line up and secure the reference tape of the wire harness to the tip of the roof headlining assembly.

3. INSTALL VANITY LIGHT ASSEMBLY

(a) Engage the 3 claws and install the vanity light assembly.





HINT
Use the same procedure to install the light on the other side.

4. INSTALL ANTENNA CORD SUB-ASSEMBLY Installation

5. INSTALL ROOF HEADLINING ASSEMBLY (for Standard)

(a) Pull the roof headlining assembly into the vehicle through the front right door.





(b) Engage the 12 claws, 4 clips, and 11 fasteners.

(c) Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

(d) Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.

(e) Connect the No. 1 wire connector and engage each clamp to the front pillar LH.





6. INSTALL ROOF HEADLINING ASSEMBLY (for Glass Roof)

(a) Pull the roof headlining assembly into the vehicle through the front right door.





(b) Engage the 12 claws, 4 clips, and 21 fasteners.

(c) Connect the antenna cord sub-assembly connector and engage the clamp to the rear pillar RH.

(d) Connect the antenna cord sub-assembly connector and engage each clamp to the front pillar RH.

(e) Connect the No. 1 wire connector and engage each clamp to the front pillar LH.





7. INSTALL ASSIST GRIP SUB-ASSEMBLY

(a) Engage the 2 clips to the assist grip sub-assembly as shown in the illustration.

(b) Install the assist grip sub-assembly.





(c) Install the 2 assist grip covers to the assist grip sub-assembly.

HINT
Use the same procedure for the other 3 assist grips.

8. INSTALL INTERIOR ILLUMINATION LIGHT ASSEMBLY (for Standard)

(a) Connect the connector.





(b) Engage the 2 clips and install the interior illumination light assembly.





9. INSTALL INTERIOR ILLUMINATION LIGHT ASSEMBLY (for Glass Roof)

(a) Connect the connector.





(b) Engage the 2 clips and install the interior illumination light assembly.





10. INSTALL SPOT LIGHT ASSEMBLY LH

(a) Connect the connector.

(b) Engage the 2 clips.





(c) Install the spot light assembly LH with the screw.





11. INSTALL SPOT LIGHT ASSEMBLY RH

HINT
Use the same procedure to install the spot light assembly on the other side.

12. INSTALL VISOR HOLDER

(a) Set the claws of the visor holder as shown in the illustration.





(b) Engage the claws and install the visor holder.

HINT
Use the same procedure to install the holder on the other side.

13. INSTALL VISOR ASSEMBLY LH

(a) Install the visor assembly LH with the 2 screws.





14. INSTALL VISOR ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

15. INSTALL VISOR BRACKET COVER

(a) Engage the 4 claws and install the visor bracket cover.





HINT
Use the same procedure to install the cover on the other side.

16. INSTALL ROOF CONSOLE BOX ASSEMBLY

(a) Connect the connectors.





(b) Engage the 2 clips.

(c) Install the roof console box assembly with the 2 screws.





(d) Engage the 2 claws.





17. INSTALL RAIN SENSOR COVER Installation

18. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER Installation

19. INSTALL FLOOR CARPET BRACKET LH

20. INSTALL FLOOR CARPET BRACKET RH

21. INSTALL SHIFT LEVER ASSEMBLY Installation

22. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY Installation

23. INSTALL NO. 2 CONSOLE BOX DUCT Installation

24. INSTALL NO. 3 CONSOLE BOX DUCT Installation

25. INSTALL REAR CONSOLE BOX ASSEMBLY Installation

26. INSTALL CONSOLE REAR END PANEL SUB-ASSEMBLY Installation

27. INSTALL CONSOLE BOX CARPET Installation

28. INSTALL CONSOLE BOX POCKET Installation

29. INSTALL HEATER SEAT SWITCH CONSOLE BASE (w/o Seat Heater System) Installation

30. INSTALL HEATER SEAT SWITCH CONSOLE BASE (w/ Seat Heater System) Installation

31. INSTALL UPPER CONSOLE PANEL ASSEMBLY WITH FRONT ASH RECEPTACLE Installation

32. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY Installation

33. INSTALL INSTRUMENT PANEL FINISH PANEL END LH Installation

34. INSTALL INSTRUMENT PANEL FINISH PANEL END RH Installation

35. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH

(a) Engage the claw and 5 clips, and install the roof side inner garnish assembly LH.





36. INSTALL REAR SEAT SIDE AIRBAG ASSEMBLY LH Installation

37. INSTALL UPPER CENTER PILLAR GARNISH LH

(a) Engage the clip.





(b) Install the upper center pillar garnish LH with the 2 screws.

38. INSTALL LOWER CENTER PILLAR GARNISH LH

(a) Engage the 5 clips and 2 claws, and install the lower center pillar garnish LH.





39. INSTALL REAR DOOR SCUFF PLATE LH

(a) Engage the 8 claws, then install the rear door scuff plate LH.





40. INSTALL FRONT PILLAR GARNISH LH

(a) Remove the protective cover.





(b) Make sure that the front pillar garnish clip is not damaged.





NOTICE:
* If there is any damage, replace the garnish clip with a new one.
* When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

(c) Engage the guide.

(d) Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.

HINT
Tape the tips of the needle-nosed pliers before use.

41. INSTALL SIDE INSTRUMENT PANEL LH Installation

42. INSTALL FRONT DOOR OPENING TRIM COVER LH

(a) Engage the 3 claws and install the front door opening trim cover LH.





43. INSTALL FRONT DOOR SCUFF PLATE LH

(a) Engage the 12 claws, and install the front door scuff plate LH.





44. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

45. INSTALL REAR SEAT SIDE AIRBAG ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

46. INSTALL UPPER CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

47. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

48. INSTALL REAR DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

49. INSTALL FRONT PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

50. INSTALL SIDE INSTRUMENT PANEL RH Installation

51. INSTALL FRONT DOOR OPENING TRIM COVER RH

HINT
Use the same procedure for the RH side and the LH side.

52. INSTALL FRONT DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

53. INSTALL FRONT SEAT ASSEMBLY LH Installation

54. INSTALL FRONT SEAT REAR OUTER TRACK BRACKET COVER LH Installation

55. INSTALL FRONT SEAT REAR INNER TRACK BRACKET COVER LH Installation

56. INSTALL FRONT SEAT OUTER TRACK BRACKET COVER LH Installation

57. INSTALL FRONT SEAT INNER TRACK BRACKET COVER LH Installation

58. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH Installation

59. INSTALL SEAT BELT ANCHOR COVER CAP LH Installation

60. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Driver Seat)

61. INSTALL FRONT SEAT ASSEMBLY RH Installation

62. INSTALL FRONT SEAT REAR OUTER TRACK BRACKET COVER RH Installation

63. INSTALL FRONT SEAT REAR INNER TRACK BRACKET COVER RH Installation

64. INSTALL FRONT SEAT OUTER TRACK BRACKET COVER RH Installation

65. INSTALL FRONT SEAT INNER TRACK BRACKET COVER RH Installation

66. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH Installation

67. INSTALL SEAT BELT ANCHOR COVER CAP RH Installation

68. INSTALL FRONT SEAT HEADREST ASSEMBLY (for Front Passenger Seat)

69. INSTALL REAR SEATBACK ASSEMBLY Installation

70. INSTALL REAR CENTER SEAT HEADREST ASSEMBLY

71. INSTALL REAR SEAT HEADREST ASSEMBLY

72. INSTALL REAR SEAT CUSHION ASSEMBLY Installation

73. PERFORM INITIALIZATION

NOTICE:
Some systems need initialization after reconnecting the cable to the negative battery terminal Repair Instruction - Initialization.

74. INSPECT SHIFT LEVER POSITION Adjustments

75. ADJUST SHIFT LEVER POSITION Adjustments

76. INSPECT FRONT SEAT ASSEMBLY Installation

77. INSPECT SRS WARNING LIGHT

Diagnosis System