Installation
INTERIOR PANELS / TRIM: ROOF HEADLINING: INSTALLATION
1. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)
(a) Put the roof headlining assembly into the vehicle through the back door.
NOTICE:
Do not damage the roof headlining assembly or body interior.
(b) Install the 3 clips.
(c) Engage the 3 clamps and connect the 2 connectors to the front pillar LH.
(d) w/o Satellite Radio:
(1) Engage the 3 clamps and connect the connector to the front pillar RH.
(2) Connect the connector to the rear pillar RH.
(e) w/ Satellite Radio:
(1) Engage the 3 clamps and connect the 2 connectors to the front pillar RH.
(2) Connect the 2 connectors to the rear pillar RH.
(f) w/ EC Mirror
(1) Connect the inner rear view mirror connector.
(g) w/ Humidity Sensor
(1) Connect the humidity sensor connector.
(h) w/ Rain Sensor
(1) Connect the rain sensor connector
2. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)
(a) Put the roof headlining assembly into the vehicle through the back door.
NOTICE:
Do not damage the roof headlining assembly or body interior.
(b) Install the 3 clips.
(c) Connect the connector to the sliding roof drive gear assembly.
(d) Engage the 3 clamps and connect the 2 connectors to the front pillar LH.
(e) w/o Satellite Radio:
(1) Engage the 3 clamps and connect the connector to the front pillar RH.
(2) Connect the connector to the rear pillar RH.
(f) w/ Satellite Radio:
(1) Engage the 3 clamps and connect the 2 connectors to the front pillar RH.
(2) Connect the 2 connectors to the rear pillar RH.
(g) w/ EC Mirror
(1) Connect the inner rear view mirror connector.
(h) w/ Humidity Sensor
(1) Connect the humidity sensor connector.
(i) w/ Rain Sensor
(1) Connect the rain sensor connector
3. INSTALL VISOR HOLDER
(a) Engage the 2 claws.
(b) Push in the visor holder as shown in the illustration.
HINT
Use the same procedure as for the other visor holder.
4. INSTALL SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)
(a) Align the alignment mark (green) on the moulding with the notch of the roof headlining to install the sliding roof opening trim moulding.
Text in Illustration
NOTICE:
After installation, check that the corners fit correctly.
5. INSTALL VISOR ASSEMBLY LH
(a) Install the visor assembly LH with the 2 screws.
6. INSTALL VISOR BRACKET COVER (for LH Side)
(a) Engage the 4 claws to install the visor bracket cover LH.
7. INSTALL VISOR ASSEMBLY RH
HINT
Use the same procedure as for the LH side.
8. INSTALL VISOR BRACKET COVER (for RH Side)
HINT
Use the same procedure as for the LH side.
9. INSTALL ASSIST GRIP SUB-ASSEMBLY
(a) Assemble the assist grip sub-assembly as shown in the illustration.
(b) Install the assist grip sub-assembly.
HINT
Use the same procedure as for the other 3 assist grip sub-assemblies.
10. INSTALL PROTECTOR (w/ Humidity Sensor) Installation
11. INSTALL RAIN SENSOR COVER (w/ Rain Sensor) Installation
12. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror) Installation
13. INSTALL NO. 1 ROOM LIGHT ASSEMBLY Installation
14. INSTALL MAP LIGHT ASSEMBLY Installation
15. INSTALL BACK DOOR WEATHERSTRIP
(a) Install a new back door weatherstrip so that the alignment marks, joint and sections indicated by the arrows, are aligned as shown in the illustration.
Text in Illustration
NOTICE:
After installation, check that the corners fit correctly.
16. INSTALL UPPER INSTRUMENT PANEL ASSEMBLY
Installation
17. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY LH
(a) Pass the floor anchor of the rear seat outer belt assembly LH through the roof side inner garnish assembly LH.
(b) Engage the 8 clips to install the roof side inner garnish assembly LH.
(c) Engage the 2 guides.
(d) Engage the 3 claws to connect the belt guide.
18. INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
(a) Engage the 4 claws and 3 clips.
(b) Install the deck trim side panel assembly LH with the 3 screw.
19. CONNECT REAR SEAT OUTER BELT ASSEMBLY LH Installation
20. INSTALL TONNEAU COVER HOLDER CAP (for LH Side)
(a) Engage the guide.
(b) Engage the claw to install the tonneau cover holder cap.
21. INSTALL TONNEAU COVER HOOK (for LH Side)
(a) Engage the 2 claws and pin to install the tonneau cover hook.
22. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for LH Side)
(a) Engage the guide.
(b) Install the luggage hold belt striker assembly with the bolt.
23. INSTALL ROPE HOOK ASSEMBLY (for LH Side)
(a) Install the rope hook assembly with the bolt.
(b) Engage the 2 claws.
24. INSTALL REAR SEAT SIDE GARNISH LH
(a) Engage the 6 claws.
(b) Install the rear seat side garnish LH with the clip.
25. INSTALL ROOF SIDE INNER GARNISH ASSEMBLY RH
HINT
Use the same procedure as for the LH side.
26. INSTALL DECK TRIM SIDE PANEL ASSEMBLY RH
HINT
Use the same procedure as for the LH side.
27. INSTALL REAR SEAT OUTER BELT ASSEMBLY RH
HINT
Use the same procedure as for the LH side.
28. INSTALL NO. 2 ROOM LIGHT ASSEMBLY Installation
29. INSTALL TONNEAU COVER HOLDER CAP (for RH Side)
HINT
Use the same procedure as for the LH side.
30. INSTALL TONNEAU COVER HOOK (for RH Side)
(a) Engage the 2 claws and pin to install the tonneau cover hook.
31. INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY (for RH Side)
HINT
Use the same procedure as for the LH side.
32. INSTALL ROPE HOOK ASSEMBLY (for RH Side)
HINT
Use the same procedure as for the LH side.
33. INSTALL REAR SEAT SIDE GARNISH RH
HINT
Use the same procedure as for the LH side.
34. INSTALL REAR SEAT SIDE COVER RH
(a) Engage the 3 claws and 2 clips to install the rear seat side cover RH.
35. INSTALL CENTER PILLAR UPPER GARNISH LH
(a) Pass the floor anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH.
(b) Engage the 2 clips.
(c) Install the center pillar upper garnish LH with the screw.
36. INSTALL CENTER PILLAR LOWER GARNISH LH
(a) Engage the 4 claws and 2 clips to install the center pillar lower garnish LH.
37. CONNECT FRONT SEAT OUTER BELT ASSEMBLY LH Installation
38. INSTALL LAP BELT OUTER ANCHOR COVER (for LH Side) Installation
39. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
(a) Align the alignment mark (purple) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
Text in Illustration
NOTICE:
After installation, check that the corners fit correctly.
40. INSTALL REAR DOOR SCUFF PLATE LH
(a) Engage the 4 claws, 2 guides and 2 clips to install the rear door scuff plate LH.
41. INSTALL FRONT PILLAR GARNISH LH
(a) Remove the protective cover.
(b) Make sure that the front pillar garnish clip is not damaged.
Text in Illustration
NOTICE:
* If there is any damage, replace the garnish clip with a new one.
* When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.
(c) Engage the 2 guides by moving the garnish in the direction indicated by the arrow (1).
(d) Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.
HINT
Tape the tips of the needle-nosed pliers before use.
(e) Engage the 2 clips to install the front pillar garnish LH.
42. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
(a) Align the alignment mark (orange) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
Text in Illustration
NOTICE:
After installation, check that the corners fit correctly.
43. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
(a) Engage the claw and clip.
NOTICE:
* Be sure to engage the clip securely.
* If there is any damage, replace the garnish clip with a new one.
(b) Install the cowl side trim board LH with the clip.
44. INSTALL FRONT DOOR SCUFF PLATE LH
(a) Engage the 4 claws, 2 guides and 4 clips to install the front door scuff plate LH.
45. INSTALL CENTER PILLAR UPPER GARNISH RH
HINT
Use the same procedure as for the LH side.
46. INSTALL CENTER PILLAR LOWER GARNISH RH
HINT
Use the same procedure as for the LH side.
47. CONNECT FRONT SEAT OUTER BELT ASSEMBLY RH
HINT
Use the same procedure as for the LH side.
48. INSTALL LAP BELT OUTER ANCHOR COVER (for RH Side)
HINT
Use the same procedure as for the LH side.
49. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
(a) Align the alignment mark (yellow green) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the rear door opening trim weatherstrip LH.
Text in Illustration
NOTICE:
After installation, check that the corners fit correctly.
50. INSTALL REAR DOOR SCUFF PLATE RH
HINT
Use the same procedure as for the LH side.
51. INSTALL FRONT PILLAR GARNISH RH
HINT
Use the same procedure as for the LH side.
52. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
(a) Align the alignment mark (light blue) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
Text in Illustration
NOTICE:
After installation, check that the corners fit correctly.
53. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH
HINT
Use the same procedure as for the LH side.
54. INSTALL FRONT DOOR SCUFF PLATE RH
HINT
Use the same procedure as for the LH side.
55. INSTALL FRONT SEAT ASSEMBLY LH
for Manual Seat Installation
for Power Seat Installation
56. INSTALL FRONT SEAT ASSEMBLY RH
HINT
Use the same procedure as for the LH side.
57. INSTALL REAR DECK TRIM COVER
(a) Engage the 4 clips to install the rear deck trim cover.
58. INSTALL DECK TRIM SERVICE HOLE COVER
(a) Engage the 2 guides (B).
(b) Engage the 2 claws and guide (A) to install the deck trim service hole cover.
59. INSTALL REAR NO. 1 FLOOR BOARD
(a) Engage the 2 claws and 2 clips.
(b) Install the rear No. 1 floor board with the bolt.
60. INSTALL REAR NO. 2 FLOOR BOARD SUB-ASSEMBLY
(a) Engage the claw and 2 clips to install the rear No. 2 floor board sub-assembly.
61. INSTALL REAR NO. 1 FLOOR BOARD SUB-ASSEMBLY
(a) Engage the 2 claws and 2 clips to install the rear No. 1 floor board sub-assembly.
62. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
(a) Install the tonneau cover assembly.
63. INSTALL DECK FLOOR BOX LH (w/o Woofer)
(a) Engage the 6 guides.
(b) Install the deck floor box LH with the clip.
64. INSTALL REAR NO. 4 FLOOR BOARD (w/o Woofer)
(a) Install the rear No. 4 floor board.
65. INSTALL REAR NO. 4 FLOOR BOARD (w/ Woofer)
(a) Engage the 2 clips and 3 guides to install the rear No. 4 floor board.
66. INSTALL REAR SEATBACK ASSEMBLY RH Installation
67. INSTALL REAR SEATBACK ASSEMBLY LH Installation
68. INSTALL REAR SEAT CUSHION LOCK HOOK Installation
69. INSTALL REAR SEAT CUSHION ASSEMBLY Installation
70. INSTALL REAR FLOOR BOARD UPPER NO. 3 PLATE
(a) Engage the 4 claws and 2 guides to install the rear floor board upper No. 3 plate.
71. INSTALL DECK FLOOR BOX RH
(a) Engage the 6 guides.
(b) Install the deck floor box RH with the clip.
72. INSTALL REAR NO. 3 FLOOR BOARD
(a) Install the rear No. 3 floor board.
73. INSTALL REAR DECK FLOOR BOX
(a) Install the rear deck floor box.
74. INSTALL REAR NO. 2 FLOOR BOARD
(a) Install the rear No. 2 floor board.