Operation CHARM: Car repair manuals for everyone.
Home >> Lexus >> 2012 >> IS F V8-5.0L (2UR-GSE) >> Repair and Diagnosis >> Body and Frame >> Interior Moulding / Trim >> Headliner >> Service and Repair >> Removal

Removal





INTERIOR PANELS / TRIM: ROOF HEADLINING: REMOVAL

1. PRECAUTION (w/ Navigation System)

NOTICE:
After the engine switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the engine switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.

2. REMOVE FRONT SEAT HEADREST ASSEMBLY

3. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER LH Removal

4. REMOVE FRONT INNER SEAT TRACK BRACKET COVER LH Removal

5. REMOVE REAR OUTER SEAT TRACK BRACKET COVER LH Removal

6. REMOVE REAR INNER SEAT TRACK BRACKET COVER LH Removal

7. REMOVE FRONT SEAT ASSEMBLY LH Removal

8. REMOVE FRONT SEAT HEADREST ASSEMBLY

9. REMOVE FRONT OUTER SEAT TRACK BRACKET COVER RH

HINT
Use the same procedure for the RH side and LH side.

10. REMOVE FRONT INNER SEAT TRACK BRACKET COVER RH

HINT
Use the same procedure for the RH side and LH side.

11. REMOVE REAR OUTER SEAT TRACK BRACKET COVER RH

HINT
Use the same procedure for the RH side and LH side.

12. REMOVE REAR INNER SEAT TRACK BRACKET COVER RH

HINT
Use the same procedure for the RH side and LH side.

13. REMOVE FRONT SEAT ASSEMBLY RH

HINT
Use the same procedure for the RH side and LH side.

14. REMOVE REAR SEAT CUSHION ASSEMBLY Removal

15. REMOVE REAR SEAT HEADREST ASSEMBLY LH

16. REMOVE REAR SEAT HEADREST ASSEMBLY RH

17. REMOVE REAR SEATBACK ASSEMBLY Removal

18. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

19. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

20. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY Removal

21. REMOVE UPPER NO. 1 CONSOLE PANEL GARNISH Removal

22. REMOVE UPPER NO. 2 CONSOLE PANEL GARNISH Removal

23. REMOVE CONSOLE PANEL SUB-ASSEMBLY Removal

24. REMOVE INSTRUMENT PANEL BOX ASSEMBLY (w/o Ashtray) Removal

25. REMOVE FRONT ASH RECEPTACLE BOX SUB-ASSEMBLY (w/ Ashtray) Removal

26. REMOVE REAR ASH RECEPTACLE ASSEMBLY (w/ Ashtray) Removal

27. REMOVE CONSOLE BOX REGISTER ASSEMBLY (w/o Ashtray) Removal

28. REMOVE CONSOLE BOX REGISTER ASSEMBLY (w/ Ashtray) Removal

29. REMOVE CONSOLE BOX Removal

30. REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY Removal

31. REMOVE CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL Removal

32. REMOVE DISPLAY AND NAVIGATION MODULE DISPLAY WITH RADIO RECEIVER ASSEMBLY (w/ Multi-display) Removal

33. REMOVE INTEGRATION CONTROL PANEL WITH RADIO RECEIVER ASSEMBLY (w/o Multi-display) Removal

34. REMOVE LOWER NO. 3 STEERING WHEEL COVER Removal

35. REMOVE LOWER NO. 2 STEERING WHEEL COVER Removal

36. REMOVE STEERING PAD Removal

37. REMOVE STEERING WHEEL ASSEMBLY Removal

38. REMOVE STEERING COLUMN COVER Removal

39. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY Removal

40. REMOVE FRONT DOOR SCUFF PLATE LH

(a) Put protective tape around the front door scuff plate.





(b) Using a moulding remover, disengage the 4 clips.

(c) Disengage the 7 claws and remove the front door scuff plate LH.





41. REMOVE FRONT DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and LH side.

42. REMOVE FRONT DOOR OPENING TRIM COVER LH

(a) Disengage the 4 claws and remove the front door opening trim cover LH.





43. REMOVE FRONT DOOR OPENING TRIM COVER RH

HINT
Use the same procedure for the RH side and LH side.

44. REMOVE FRONT PILLAR GARNISH LH

(a) Pull the upper part of the garnish toward the inside of the cabin and disengage the garnish from the base of the 2 clips.





HINT
Make the front pillar garnish LH hang down from the front pillar garnish clip.

(b) Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and remove it from the front pillar garnish LH.





NOTICE:
* Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.
* Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

(c) Disengage the guide at the front end of the front pillar garnish LH and remove it.

(d) Protect the curtain shield airbag assembly.





(1) Thoroughly cover the airbag with a cloth or nylon sheet and fix the ends of the cover with adhesive tape, as shown in the illustration.

NOTICE:
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.

45. REMOVE FRONT PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and LH side.

46. REMOVE SIDE INSTRUMENT PANEL LH Removal

47. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Removal

48. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY Removal

49. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY Removal

50. REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY Removal

51. REMOVE COMBINATION METER ASSEMBLY Removal

52. REMOVE SIDE INSTRUMENT PANEL RH Removal

53. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Removal

54. REMOVE FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY Removal

55. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY Removal

56. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY Removal

57. REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY Removal

58. REMOVE NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY Removal

59. REMOVE FRONT STEREO COMPONENT SPEAKER ASSEMBLY (w/ Front Center Speaker) Removal

60. REMOVE NO. 2 CONSOLE BOX DUCT Removal

61. REMOVE NO. 1 CONSOLE BOX DUCT Removal

62. DISCONNECT NO. 2 INSTRUMENT PANEL WIRE Removal

63. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY Removal

64. REMOVE INSTRUMENT PANEL CLIP Removal

65. REMOVE INSTRUMENT PANEL STAY Removal

66. REMOVE NO. 2 FLOOR UNDER COVER Removal

67. REMOVE NO. 1 FLOOR UNDER COVER Removal

68. REMOVE TAIL EXHAUST PIPE ASSEMBLY Removal

69. REMOVE REAR NO. 1 FLOOR PANEL BRACE Removal

70. REMOVE FRONT CENTER FLOOR BRACE Removal

71. DISCONNECT HEATED OXYGEN SENSOR Removal

72. REMOVE FRONT EXHAUST PIPE ASSEMBLY Removal

73. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR Removal

74. REMOVE FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY Removal

75. REMOVE TRANSMISSION FLOOR SHIFT ASSEMBLY Removal

76. REMOVE REAR DOOR SCUFF PLATE LH

(a) Put protective tape around the rear door scuff plate.





(b) Using a moulding remover, disengage the 2 clips.

(c) Disengage the 5 claws and remove the the rear door scuff plate LH.





77. REMOVE REAR DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and LH side.

78. REMOVE LAP BELT OUTER ANCHOR COVER LH

(a) Disengage the 2 claws and remove the lap belt outer anchor cover LH.





79. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY LH

(a) Remove the bolt and separate the front seat outer belt assembly LH.





80. REMOVE LOWER CENTER PILLAR GARNISH LH

(a) Disengage the 3 claws and 5 clips, and remove the lower center pillar garnish LH.





81. REMOVE CENTER PILLAR GARNISH LH

(a) Remove the 2 screws.





(b) Disengage the 2 claws and remove the center pillar garnish LH by pulling it down.

82. REMOVE FRONT SEAT BELT ANCHOR COVER SUB-ASSEMBLY

(a) Disengage the 3 claws and remove the front seat belt anchor cover sub-assembly.





83. REMOVE LOWER CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and LH side.

84. SEPARATE FRONT SEAT OUTER BELT ASSEMBLY RH

(a) Disconnect the connector.





(b) Remove the bolt and separate the front seat outer belt assembly RH.

85. REMOVE CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and LH side.

86. REMOVE REAR SEAT SIDE GARNISH LH

(a) Disengage the 5 claws and remove the rear seat side garnish LH.





87. REMOVE REAR SEAT SIDE GARNISH RH

HINT
Use the same procedure for the RH side and LH side.

88. REMOVE ROOF SIDE INNER GARNISH LH

(a) Disengage the 4 clips and claw, and remove the roof side inner garnish LH.





89. REMOVE ROOF SIDE INNER GARNISH RH

HINT
Use the same procedure for the RH side and LH side.

90. REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER Removal

91. REMOVE RAIN SENSOR Removal

92. REMOVE MAP LIGHT ASSEMBLY (w/o Sliding Roof) Service and Repair

93. REMOVE MAP LIGHT ASSEMBLY (w/ Sliding Roof) Service and Repair

94. REMOVE SPOT LIGHT ASSEMBLY Removal

95. REMOVE COAT HOOK

(a) Remove the screw and coat hook.





HINT
Use the same procedure to remove the hook on the other side.

96. REMOVE ASSIST GRIP SUB-ASSEMBLY

(a) Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.





HINT
Tape the screwdriver tip before use.

(b) Disengage the 2 clips and remove the assist grip sub-assembly.

HINT
Use the same procedure for the other 3 assist grips.

97. REMOVE VISOR BRACKET COVER

(a) Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.





HINT
Use the same procedure to remove the cover on the other side.

98. REMOVE VISOR ASSEMBLY LH

(a) Remove the 2 screws and visor assembly LH.





99. REMOVE VISOR ASSEMBLY RH

HINT
Use the same procedure for the RH side and LH side.

100. REMOVE VISOR HOLDER

(a) Remove the visor holder by turning it counterclockwise.





HINT
Use the same procedure to remove the holder on the other side.

101. REMOVE ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

(a) Disconnect the roof wire connector and disengage each clamp from the front pillar LH.





(b) Disconnect each connector from the map light assembly.

(c) Disengage the hook, 10 claws and 2 clips.





(d) Remove the roof headlining assembly from the vehicle through the front right door.





102. REMOVE ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

(a) Disconnect the roof wire connector and disengage each clamp from the front pillar LH.





(b) Disconnect each connector from the map light assembly.

(c) Disengage the hook, 10 claws, 8 fasteners and 2 clips.





(d) Remove the roof headlining assembly from the vehicle through the front right door.





103. REMOVE ROOF HEADLINING PAD

(a) Remove the 2 roof headlining pads.





104. REMOVE NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)

(a) Remove the No. 1 roof silencer pad.





105. REMOVE CENTER ROOF SILENCER PAD (w/o Sliding Roof)

(a) Remove the center roof silencer pad.





106. REMOVE ROOF HEADLINING PAD LH (w/o Sliding Roof)

(a) Remove the 2 roof headlining pads LH.





107. REMOVE REAR ROOF SILENCER PAD (w/o Sliding Roof)

(a) Remove the 2 rear roof silencer pads.





108. REMOVE REAR NO. 2 SIDE RAIL SPACER LH (w/o Sliding Roof)

(a) Remove the rear No. 2 side rail spacer LH.





109. REMOVE REAR NO. 2 SIDE RAIL SPACER RH (w/o Sliding Roof)

HINT
Use the same procedure for the RH side and LH side.

110. REMOVE REAR SIDE RAIL SPACER LH (w/ Sliding Roof)

(a) Remove the rear side rail spacer LH.





111. REMOVE REAR SIDE RAIL SPACER RH (w/ Sliding Roof)

HINT
Use the same procedure for the RH side and LH side.

112. REMOVE NO. 2 ROOF HEADLINING PAD

(a) Remove the 2 No. 2 roof headlining pads.





113. REMOVE VANITY LIGHT ASSEMBLY

(a) Disengage the claw [A] and separate the bulb holder from the vanity light, as shown in the illustration.





(b) Disengage the claw [B] and remove the vanity light assembly.

HINT
Use the same procedure to remove the light on the other side.

114. REMOVE NO. 1 ROOF WIRE

(a) Remove the double-sided tape and roof wire.

115. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH

116. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

117. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH

118. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
pro multis · About Operation CHARM