P0016
2UR-FSE ENGINE CONTROL SYSTEM: SFI SYSTEM: P0016, P0018: Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)
P0018 - Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)
DESCRIPTION
Refer to DTC P0010 P0010.
MONITOR DESCRIPTION
These DTCs are output when a valve timing deviation condition is detected. While the vehicle is being driven or the engine is idling (after the battery terminals are reconnected), if a valve timing deviation is detected during the valve timing initialization operation, it is determined that a malfunction has occurred. If this condition is detected while driving, a DTC is output (2 trip detection logic). However, if the valve timing is deviated, the camshaft position sensor malfunction DTC P1340 may be output.
A DTC is output if the following occurs: 1) the engine is idled, and then the power switch is turned off; and 2) the engine is started and the engine is idled.
DTC P0016 and/or P0018 may be output if the battery is reconnected and the engine is started while the following are disconnected from the camshaft timing control motor: 1) power source harness or connector; or 2) ECM harness or connector.
If P0016 and/or P0018 is output, check if the harness or connector is disconnected.
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
CONFIRMATION DRIVING PATTERN
1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG) and turn the Techstream on.
3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure) Reading and Clearing Diagnostic Trouble Codes.
4. Turn the power switch off.
5. Turn the power switch on (IG) and turn the Techstream on [A].
6. Put the engine in inspection mode Component Tests and General Diagnostics.
7. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or more [B].
8. Idle the engine for 5 minutes or more [C].
9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending [D].
10. Read the pending DTC.
11. If a pending DTC is output, the system is malfunctioning.
HINT
If a pending DTC is not output, perform the following procedure.
12. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
13. Input the DTC: P0016 or P0018.
14. Check the DTC judgment result.
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
HINT
- If the judgment result shows ABNORMAL, the system has a malfunction.
- If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].
15. Drive the vehicle for 2 to 3 minutes [E].
16. Idle the engine for 5 minutes or more [F].
17. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
18. Input the DTC: P0016 or P0018.
19. Check the DTC judgment result [G].
HINT
If the judgment result shows ABNORMAL, the system has a malfunction.
20. If the test result is INCOMPLETE or N/A, perform a universal trip and check for permanent DTCs Reading and Clearing Diagnostic Trouble Codes.
HINT
- If a permanent DTC is output, the system is malfunctioning.
- If no permanent DTC is output, the system is normal.
INSPECTION PROCEDURE
HINT
- By using the Active Test's Control the VVT-iE Linear (Bank 1) or Control the VVT-iE Linear (Bank 2) function, it can be determined if the VVT system for intake side is malfunctioning.
(1) Connect the Techstream to the DLC3.
(2) Turn the power switch on (IG) and turn the Techstream ON.
(3) Put the engine in inspection mode Inspection Mode Procedure.
(4) Warm up the engine.
(5) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT-iE Linear (Bank 1) or Control the VVT-iE Linear (Bank 2) / All Data / VVT-iE Aim Angle #1 and VVT Change Angle #1 or VVT-iE Aim Angle #2 and VVT Change Angle #2.
(6) Perform the Active Test operation with the engine speed at 1500 rpm.
OK:
- Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
- Bank 2 refers to the bank that does not include the No. 1 cylinder.
PROCEDURE
1. CHECK ANY OTHER DTCS OUTPUT (P0016 OR P0018)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG) and turn the Techstream ON.
(c) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(d) Read the DTCs.
Result
B -- GO TO DTC CHART SFI System
A -- Continue to next step.
2. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 1 and/or Bank 2)
(a) Turn the power switch off.
(b) Remove the camshaft timing control motor (for Bank 1 and/or Bank 2) Removal.
(c) Check if the camshaft timing gear assembly's eccentric shaft rotates smoothly.
OK:
Rotates smoothly
NG -- REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (for Bank 1 and/or Bank 2) Removal
OK -- Continue to next step.
3. INSPECT VALVE TIMING
(a) Remove the cylinder head cover LH and RH.
(b) Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.
(c) Check that the timing marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.
OK:
Timing marks on camshaft timing gears are aligned as shown in the illustration.
(d) Reinstall the cylinder head cover LH and RH.
NG -- ADJUST VALVE TIMING Reassembly
OK -- Continue to next step.
4. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
(a) To initialize the ECM's valve timing, disconnect the cable from the negative (-) battery terminal for 1 minute.
(b) Connect the cable to the negative (-) battery terminal Service Precautions.
(c) Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
(d) Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
(e) Read the DTCs.
Result
B -- GO TO DTC CHART SFI System
A -- END