Mechanical System Test
MECHANICAL SYSTEM TEST [RC4A-EL]Mechanical System Test Preparation
1. Engage the parking brake and use wheel chocks at the front and rear of the wheels.
2. Inspect the engine coolant level.
3. Inspect the engine oil level.
4. Inspect the ATF level.
5. Inspect the idle speed and ignition timing in the P position.
6. Wait until the engine and transmission reach normal operating temperature.
Line Pressure Test
1. Perform mechanical system test preparation.
Warning: Removing the square head plug when the ATF is hot can be dangerous. Hot ATF can come out of the opening and badly burn you. Before removing the square head plug, allow the ATF to cool.
2. Connect the SSTs (49 HD64 406A, 49 0378 400B) to the line pressure inspection port and replace the gauge of the SST (49 0378 400B) with the SST (49 B019 901B).
3. Start the engine and warm it up until the ATF reaches 60-70°C (140-158°F).
4. Shift the selector lever to the D range.
5. Read the line pressure while the engine is idling for the D range.
6. Read the line pressure while the engine is idling for the P, R, N positions and M range in the same manner as in Steps 4-5.
7. Stop the engine, then replace the SST (49 B019 901B) with the gauge of the SST (49 0378 400B).
8. Start the engine.
9. Firmly depress the brake pedal with the left foot. 10, Shift the selector lever to the D range.
Caution: If the accelerator pedal is pressed for more than 5 s while the brake pedal is pressed, the transmission could be damaged. Therefore, perform Steps 11 and 12 within 5 s.
11. Gradually depress the accelerator pedal with the right foot.
12. When the engine speed no longer increases, quickly read the line pressure and release the accelerator pedal.
13. Shift the selector lever to the Nm position and idle the engine for 1 min or more to cool the ATF
14. Read the line pressure at the engine stall speed for the M range and R position in the same manner as in Steps 9-13.
Line Pressure:
Warning: Removing the square head plug when the ATF is hot can be dangerous. Hot ATF can come out of the opening and badly burn you. Before removing the square head plug, allow the ATF to cool.
15. Remove the SSTs.
16. Install a new square head plug and O-ring in the inspection port.
Tightening torque 10.8-12.7 N-m {110-130 kgf-cm, 96-112 in-lbf}
Evaluation of line pressure test
Evaluation Of Line Pressure Test:
Stall Speed Test
1. Perform mechanical system test preparation. (See Mechanical System Test Preparastion.) Mechanical System Test
2. Start the engine.
3. Firmly depress the brake pedal with the left foot.
4. Shift the selector lever to the D range.
Caution: If the accelerator pedal is pressed for more than 5 s while the brake pedal is pressed, the transmission could be damaged. Therefore, perform Steps 5 and 6 within 5 s.
5. Gently depress the accelerator pedal with the right foot.
6. When the engine speed no longer increases, quickly read the engine speed and release the accelerator pedal.
7. Shift the selector lever to the Nm position and idle the engine for I min or more to cool the ATF.
8. Perform a stall test of the M range and R position in the same manner as in Steps 3-7.
9. Turn off the engine.
Engine Stall Speed:
Evaluation Of Stall Test:
Time Lag Test
1. Perform mechanical system test preparation. (See Mechanical System Test Preparastion.) Mechanical System Test
2. Start the engine.
3. Warm up the engine until the ATF temperature reaches 60-70°C (140-158°F).
4. Shift the selector lever from the Nm position to D range.
5. Use a stopwatch to measure the time it takes from shifting until shock is felt. Take three measurements for each test and average from the results using the following formula.
Formula
Average time lag = (Time 1 + Time 2 + Time 3) / 3
6. Perform the test for the following shifts in the same manner Step 5.
^ N position --- > R position
