CVT RE0F10A
P0715 INPUT SPEED SENSOR A
Description
The primary speed sensor detects the primary pulley revolution speed and sends a signal to the TCM.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If "DTC CONFIRMATION PROCEDURE" has been previously performed, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.CHECK DTC DETECTION
With CONSULT-III
1. Turn ignition switch ON.
2. Select "DATA MONITOR".
3. Start engine and maintain the following conditions for at least 5 consecutive seconds.
With GST
Follow the procedure "With CONSULT-III".
Is "P0715" detected?
YES - Go to CVT RE0F10A.
NO - Check intermittent incident. Refer to Intermittent Incident.
Diagnosis Procedure
1.CHECK PRIMARY SPEED SENSOR
With CONSULT-III
1. Start engine.
2. Check voltage between TCM harness connector F16 terminal
25, 46 and 25, 48.
3. If OK, check pulse when vehicle cruises.
Is the inspection result normal?
YES - GO TO 12.
NO - GO TO 2.
2.CHECK POWER AND SENSOR GROUND
1. Turn ignition switch OFF.
2. Disconnect primary speed sensor harness connector.
3. Turn ignition switch ON.
4. Check voltage between primary speed sensor harness connector F8 terminal 1 and 3.
5. Check voltage between primary speed sensor harness connector F8 terminal 3 and ground.
Is the inspection result normal?
YES - GO TO 3.
NO-1 - Battery voltage is not supplied between terminals 1 and
3, terminal 3 and ground: GO TO 6.
NO-2 - Battery voltage is not supplied between terminals 1 and 3 only: GO TO 8.
3.CHECK HARNESS BETWEEN TCM AND PRIMARY SPEED SENSOR (SENSOR GROUND)
1. Turn ignition switch OFF.
2. Disconnect TCM harness connector and CVT unit harness connector.
3. Check continuity between TCM harness connector F16 terminal
33 and ground.
Is the inspection result normal?
YES - GO TO 4.
NO - Repair or replace damaged parts.
4.CHECK HARNESS BETWEEN TCM AND PRIMARY SPEED SENSOR (PART 1)
Check continuity between TCM harness connector F16 (A) terminal
33 and primary speed sensor harness connector F8 (B) terminal 2.
Is the inspection result normal?
YES - GO TO 5.
NO - Repair or replace damaged parts.
5.CHECK HARNESS BETWEEN TCM AND PRIMARY SPEED SENSOR (PART 2)
Check continuity between TCM harness connector F16 terminal 33 and ground.
Is the inspection result normal?
YES - GO TO 10.
NO - Repair or replace damaged parts.
6.CHECK HARNESS BETWEEN IPDM E/R AND PRIMARY SPEED SENSOR (POWER) (PART 1)
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector F10.
3. Check continuity between IPDM E/R harness connector F10 terminal 58 and primary speed sensor harness connector F8 terminal 3.
Is the inspection result normal?
YES - GO TO 7.
NO - Repair or replace damaged parts.
7.CHECK HARNESS BETWEEN IPDM E/R AND PRIMARY SPEED SENSOR (POWER) (PART 2)
Check continuity between IPDM E/R harness connector F10 terminal 58 and ground.
Is the inspection result normal?
YES - Check the following.
- Harness for short or open between ignition switch and
IPDM E/R
- 10A fuse (No. 34, located in IPDM E/R)
- Ignition switch
NO - Repair or replace damaged parts.
8.CHECK HARNESS BETWEEN TCM AND PRIMARY SPEED SENSOR (SENSOR GROUND) (PART 1)
1. Turn ignition switch OFF.
2. Disconnect TCM connector.
3. Check continuity between TCM harness connector F16 terminal
25 (A) and primary speed sensor harness connector F8 (B) terminal 1.
Is the inspection result normal?
YES - GO TO 9.
NO - Repair or replace damaged parts.
9.CHECK HARNESS BETWEEN TCM AND PRIMARY SPEED SENSOR (SENSOR GROUND) (PART 2)
1. Disconnect CVT unit harness connector.
2. Check continuity between TCM harness connector F16 terminal
25 and ground.
Is the inspection result normal?
YES - GO TO 10.
NO - Repair or replace damaged parts.
10.CHECK CVT UNIT CIRCUIT
Check continuity between CVT unit harness connector F46 terminal
19 and ground.
Is the inspection result normal?
YES - GO TO 11.
NO - Repair or replace damaged parts.
11.CHECK TCM
1. Replace same type TCM. Refer to Exploded View.
2. Connect each connector.
3. Perform "DTC CONFIRMATION PROCEDURE". Refer to CVT RE0F10A.
Is "P0715" detected?
YES - Replace primary speed sensor. Refer to Removal And Installation.
NO - Replace TCM. Refer to Exploded View.
12.DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES - Replace TCM. Refer to Exploded View.
NO - Repair or replace damaged parts.