For California

DTC P0011 IVT CONTROL





Description

SYSTEM DESCRIPTION










This mechanism hydraulically controls cam phases continuously with the fixed operating angle of the intake valve. The ECM receives signals such as crankshaft position, camshaft position, engine speed, and engine coolant temperature. Then, the ECM sends ON/OFF pulse duty signals to the intake valve timing control solenoid valve depending on driving status. This makes it possible to control the shut/open timing of the intake valve to increase engine torque in low/mid speed range and output in high-speed range.




CONSULT-III Reference Value in Data Monitor Mode
Specification data are reference values.









On Board Diagnosis Logic






FAIL-SAFE MODE
ECM enters in fail-safe mode when the malfunction is detected.









DTC Confirmation Procedure

CAUTION:
Always drive at a safe speed.

NOTE:
- If DTC P0011 is displayed with DTC P0075, first perform trouble diagnosis for DTC P0075. See For California.
- If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is between 10 V and 16 V at idle.

WITH CONSULT-III
1. Turn ignition switch ON and select "DATA MONITOR" mode with CONSULT-III.
2. Start engine and warm it up to the normal operating temperature.
3. Maintain the following conditions for at least 10 consecutive seconds.
Hold the accelerator pedal as steady as possible.





4. Let engine idle for 10 seconds.
5. Check 1st trip DTC.
6. If 1st trip DTC is detected, go to For California.
If 1st trip DTC is not detected, go to next step.
7. Maintain the following conditions for at least 10 consecutive seconds.





8. Check 1st trip DTC.
9. If 1st trip DTC is detected, go to For California.

WITH GST
Follow the procedure "WITH CONSULT-III" above.




Diagnosis Procedure
1.CHECK OIL PRESSURE WARNING LAMP
1. Start engine.





2. Check oil pressure warning lamp and confirm it is not illuminated.
OK or NG
OK - GO TO 2.
NG - Go to Procedures.
2.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE
For California.
OK or NG
OK - GO TO 3.
NG - Replace intake valve timing control solenoid valve.
3.CHECK CRANKSHAFT POSITION SENSOR (POS)
For California.
OK or NG
OK - GO TO 4.
NG - Replace crankshaft position sensor (POS).
4.CHECK CAMSHAFT POSITION SENSOR (PHASE)
For California.
OK or NG
OK - GO TO 5.
NG - Replace camshaft position sensor (PHASE).
5.CHECK CAMSHAFT (INTAKE)





Check the following.
- Accumulation of debris to the signal plate of camshaft (1) rear end
- Chipping signal plate of camshaft rear end
OK or NG
OK - GO TO 6.
NG - Remove debris and clean the signal plate of camshaft rear end or replace camshaft.
6.CHECK TIMING CHAIN INSTALLATION
Check service records for any recent repairs that may cause timing chain misaligned.
Are there any service records that may cause timing chain misaligned?
Yes or No
Yes - Check timing chain installation. Component.
No - GO TO 7.
7.CHECK LUBRICATION CIRCUIT
Removal And Installation.
OK or NG
OK - GO TO 8.
NG - Clean lubrication line.
8.CHECK INTERMITTENT INCIDENT
For California For California.
For Wiring Diagram, For California for CKP sensor (POS) and For California for CMP sensor (PHASE).
- INSPECTION END




Component Inspection

INTAKE VALVE TIMING CONTROL SOLENOID VALVE
1. Disconnect intake valve timing control solenoid valve harness connector.





2. Check resistance between intake valve timing control solenoid valve as follows.





If NG, replace intake valve timing control solenoid valve.
If OK, go to next step.
3. Remove intake valve timing control solenoid valve.





4. Provide 12 V DC between intake valve timing control solenoid valve terminals and then interrupt it. Make sure that the plunger moves as shown in the figure.

CAUTION:
Do not apply 12 V DC continuously for 5 seconds or more.
Doing so may result in damage to the coil in intake valve timing control solenoid valve.
If NG, replace intake valve timing control solenoid valve.

NOTE:
Always replace O-ring when intake valve timing control solenoid valve is removed.




Removal and Installation

INTAKE VALVE TIMING CONTROL SOLENOID VALVE
Component Removal And Installation.