P0122
DTC P0122, P0123 TP SENSOR
Component Description
Electric throttle control actuator consists of throttle control motor, throttle position sensor, etc. The throttle position sensor responds to the throttle valve movement.
The throttle position sensor has two sensors. These sensors are a kind of potentiometers which transform the throttle valve position into output voltage, and emit the voltage signal to the ECM. The ECM judges the current opening angle of the throttle valve from these signals and controls the throttle valve opening signal in response to driving conditions via the throttle control motor.
CONSULT-III Reference Value in Data Monitor Mode
Specification data are reference values.
On Board Diagnosis Logic
These self-diagnosis have the one trip detection logic.
NOTE:
If DTC P0122 or P0123 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. P0643.
FAIL-SAFE MODE
When the malfunction is detected, ECM enters fail-safe mode and the MIL illuminates.
DTC Confirmation Procedure
NOTE:
If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.
1. Start engine and let it idle for 1 second.
2. Check DTC.
3. If DTC is detected, go to P0122.
Wiring Diagram
EC-TPS2-01:
Specification data are reference values and are measured between each terminal and ground.
CAUTION:
Never use ECM ground terminals when measuring input/output voltage. Doing so may result in damage to the ECM's transistor. Use a ground other than ECM terminals, such as the ground.
Diagnosis Procedure
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Loosen and retighten ground screws on the body. Ground Inspection.
OK or NG
OK - GO TO 2.
NG - Repair or replace ground connections.
2.CHECK THROTTLE POSITION SENSOR 2 POWER SUPPLY CIRCUIT
1. Disconnect electric throttle control actuator harness connector
(1).
Arrow Indicates Vehicle front
2. Turn ignition switch ON.
3. Check voltage between electric throttle control actuator terminal
1 and ground with CONSULT-III or tester.
Voltage: Approximately 5 V
OK or NG
OK - GO TO 3.
NG - Repair open circuit or short to ground or short to power in harness or connectors.
3.CHECK THROTTLE POSITION SENSOR 2 GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check harness continuity between electric throttle control actuator terminal 4 and ECM terminal 36. Refer to Wiring Diagram.
Continuity should exist.
4. Also check harness for short to ground and short to power.
OK or NG
OK - GO TO 4.
NG - Repair open circuit or short to ground or short to power in harness or connectors.
4.CHECK THROTTLE POSITION SENSOR 2 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check harness continuity between ECM terminal 38 and electric throttle control actuator terminal 3. Refer to Wiring Diagram.
Continuity should exist.
2. Also check harness for short to ground and short to power.
OK or NG
OK - GO TO 5.
NG - Repair open circuit or short to ground or short to power in harness or connectors.
5.CHECK THROTTLE POSITION SENSOR
P0122.
OK or NG
OK - GO TO 7.
NG - GO TO 6.
6.REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1. Replace the electric throttle control actuator.
2. Perform Throttle Valve Closed Position Learning.
3. Perform Programming and Relearning.
- INSPECTION END
7.CHECK INTERMITTENT INCIDENT
Description Diagnosis Procedure.
- INSPECTION END
Component Inspection
THROTTLE POSITION SENSOR
1. Reconnect all harness connectors disconnected.
2. Perform Throttle Valve Closed Position Learning.
3. Turn ignition switch ON.
4. Set selector lever to D position (CVT) or 1st position (M/T).
5. Check voltage between ECM terminals 37 (TP sensor 1 signal), 38 (TP sensor 2 signal) and ground under the following conditions.
6. If NG, replace electric throttle control actuator and go to the next step.
7. Perform Throttle Valve Closed Position Learning.
8. Perform Programming and Relearning.
Removal and Installation
ELECTRIC THROTTLE CONTROL ACTUATOR
Service and Repair.