Front Passenger Side Power Window Does Not Operate With Front Passenger Side Power Window Switch

WINDOW / GLASS: POWER WINDOW CONTROL SYSTEM: Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch
- Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

DESCRIPTION

When the engine is running or the ignition switch is ON, the front power window regulator motor assembly RH is operated by the front power window regulator switch assembly RH. The front power window regulator motor assembly RH has motor, regulator, and ECU functions.

HINT
If the pulse sensor built into the front power window regulator motor assembly RH malfunctions, the power window control system enters fail-safe mode. The remote up/down and auto up/down functions cannot be operated during fail-safe mode. However, the power window can be closed by holding the front power window regulator switch assembly RH at the auto up position, and opened manually by pushing down the front power window regulator switch assembly RH.

WIRING DIAGRAM





INSPECTION PROCEDURE

NOTICE:
* The power window control system uses a multiplex communication system (LIN communication system). Inspect the communication function by following How to Proceed with Troubleshooting How To Proceed With Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly.
* When the front power window regulator motor assembly RH is reinstalled or replaced, the power window control system must be initialized.
* After a door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be reinitialized by repeating the following operations at least 5 times:
(1) Close the power window by fully pulling up the front power window regulator switch assembly RH and holding it at the auto up position.
(2) Open the power window by fully pushing down the front power window regulator switch assembly RH.
* When the ECU determines that the front power window regulator motor assembly RH has a malfunction, DTC B2311 is set.

PROCEDURE

1. READ VALUE USING TECHSTREAM (MAIN BODY)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Main Body / Data List.

(e) Read the Data List according to the display on the Techstream.

Main Body (Main Body ECU)





OK:

On the Techstream screen, OK is displayed.

NG -- GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting) Initial Inspection and Diagnostic Overview
OK -- Continue to next step.

2. READ VALUE USING TECHSTREAM (P-DOOR MOTOR)

(a) Enter the following menus: Body Electrical / P-Door Motor / Data List.

(b) Read the Data List according to the display on the Techstream.

P-Door Motor (Front Power Window Regulator Motor Assembly RH)





OK:

On the Techstream screen, ON or OFF is displayed accordingly.

NG -- INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
OK -- Continue to next step.

3. PERFORM ACTIVE TEST USING TECHSTREAM (P-DOOR MOTOR)

(a) Enter the following menus: Body Electrical / P-Door Motor / Active Test.

(b) Perform the Active Test according to the display on the Techstream.

P-Door Motor (Front Power Window Regulator Motor Assembly RH)





OK:

Front passenger side power window operates normally.

CAUTION:
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.

NG -- REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Removal

OK -- REPLACE MAIN BODY ECU Removal

4. INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

(a) Remove the front power window regulator switch assembly RH Removal.





(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





Text in Illustration





NG -- REPLACE FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY RH Removal
OK -- Continue to next step.

5. CHECK HARNESS AND CONNECTOR (FRONT RH SIDE SWITCH - MOTOR AND BODY GROUND)

(a) Disconnect the front power window regulator motor assembly RH connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:





NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR

OK -- REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH Removal