Installation

STEERING COLUMN: STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic):

INSTALLATION
NOTE: When installing, coat the parts indicated by arrows with molybdenum disulfide lithium base grease Components.

1. INSTALL STEERING SHAFT UNIVERSAL JOINT ASSEMBLY






(a) Align the matchmarks on the steering shaft universal joint assembly and the steering column assembly.
(b) Install the bolt.
Torque: 35 Nm (360 kgf-cm, 26 ft-lbf)
2. INSTALL STEERING COLUMN HOLE COVER SUB-ASSEMBLY NO.2
(a) Apply molybdenum disulfide lithium base grease to the lip of the steering column hole cover sub-assembly No.2.






(b) Install the steering column hole cover sub-assembly No.2 to the steering intermediate shaft sub-assembly.
3. TEMPORARILY TIGHTEN STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY






(a) Align the matchmarks on the steering intermediate shaft sub-assembly and the steering shaft universal joint assembly.
(b) Temporarily install the bolt.
HINT: Do not tighten the bolt.

4. INSTALL STEERING COLUMN ASSEMBLY






(a) Install the steering column assembly with the 2 bolts and 2 nuts.
Torque: 26 Nm (265 kgf-cm, 19 ft-lbf)
(b) Connect the connectors to the steering column assembly.
(c) Install the wire harness clamps to the steering column assembly.
5. INSTALL INSTRUMENT PANEL FINISH PLATE
6. CONNECT STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY






(a) Align matchmarks on the steering intermediate shaft sub-assembly and the power steering link assembly.






(b) Install the bolt.
Torque: 35 Nm (360 kgf-cm, 26 ft-lbf)






(c) Tighten the bolt (B).
Torque: 35 Nm (360 kgf-cm, 26 ft-lbf)
(d) Install the clamp to the steering column hole shield and tighten the bolt (A).
7. INSTALL AIR DUCT NO.1






(a) Engage the 2 claws to install the air duct No.1.
(b) Install the bolt.
8. PLACE FRONT WHEELS FACING STRAIGHT AHEAD
9. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY






(a) Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.
10. INSTALL TILT AND TELESCOPIC SWITCH






(a) Engage the claw to install the tilt and telescopic switch.
(b) Connect the connector.
11. INSTALL STEERING COLUMN COVER






(a) Engage the claw to install the steering column cover upper.






(b) Engage the 2 claws to install the steering column cover lower.
NOTE: Do not damage the tilt and telescopic switch.

(c) Install the 3 screws.
12. ADJUST SPIRAL CABLE SUB-ASSEMBLY Installation

13. INSTALL STEERING WHEEL ASSEMBLY
(a) Align the matchmarks on the steering wheel assembly and steering main shaft assembly.
(b) Install the steering wheel assembly set nut.
Torque: 50 Nm (510 kgf-cm, 37 ft-lbf)
14. INSPECT STEERING WHEEL CENTER POINT
15. INSTALL STEERING PAD Installation

16. INSTALL STEERING WHEEL NO.3 COVER LOWER Installation

17. INSTALL STEERING WHEEL NO.2 COVER LOWER Installation

18. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY Installation

19. INSTALL INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY LOWER Installation

20. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH Installation

21. INSTALL FRONT DOOR SCUFF PLATE LH Installation

22. INSTALL FRONT WHEEL LH
Torque: 103 Nm (1,050 kgf-cm, 76 ft-lbf)
23. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTE: When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

24. CHECK FOR DTCs (POWER TILT AND POWER TELESCOPIC STEERING COLUMN ) Reading and Clearing Diagnostic Trouble Codes

25. INSPECT SRS WARNING LIGHT Diagnosis System