U029A
HYBRID / BATTERY CONTROL: HYBRID BATTERY SYSTEM: U029A-123: Lost Communication with Hybrid Battery Pack Sensor Module
U029A-123 - Lost Communication with Hybrid Battery Pack Sensor Module
DESCRIPTION
The battery smart unit detects the HV battery conditions (voltage, current, and temperature) and the battery cooling fan voltage, and sends the detected signals to the power management control ECU via the serial communication system.
MONITOR DESCRIPTION
If a malfunction in communication line between the battery smart unit and power management control ECU (HV CPU) is detected, the power management control ECU (HV CPU) illuminates the MIL and sets a DTC.
MONITOR STRATEGY
TYPICAL ENABLING CONDITIONS
TYPICAL MALFUNCTION THRESHOLDS
COMPONENT OPERATING RANGE
CONFIRMATION DRIVING PATTERN
1. Connect the Techstream to the DLC3.
2. Turn the power switch on (IG) and turn the Techstream on.
3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
4. Turn the power switch off.
5. Turn the power switch on (READY) and after a few seconds, turn the power switch off. [A]
6. Repeat [A] 3 times. [B]
7. Turn the power switch on (IG) and turn the Techstream on.
8. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes. [C]
9. Check that permanent DTCs are cleared.
10. If the permanent DTCs are not cleared, perform the universal trip, and then check for permanent DTCs again.
HINT
* If a permanent DTC is output, the system is malfunctioning.
* If no permanent DTC is output, the system is normal.
WIRING DIAGRAM
INSPECTION PROCEDURE
CAUTION:
* If the battery cover is removed, install it before turning the power switch on (IG) or (READY). If the power switch is turned on (IG) or (READY) with the battery cover removed, U029A-123 may be set.
* Before inspecting the high-voltage system, take safety precautions to prevent electrical shocks, such as wearing insulated gloves and removing the service plug grip. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
* After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals.
HINT
At least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
NOTICE:
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.
PROCEDURE
1. CHECK DTC OUTPUT (HV)
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
(d) Read output DTCs Hybrid Battery System.
Result:
(e) Disconnect the Techstream from the DLC3.
B -- GO TO DTC CHART Hybrid Battery System
A -- Continue to next step.
2. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BATTERY SMART UNIT)
CAUTION:
Be sure to wear insulated gloves and protective goggles.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Disconnect the F97 connector from the power management control ECU Removal.
(c) Remove the battery smart unit Removal.
HINT
Disconnect only the z30 connector of the battery smart unit.
(d) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
(e) Remove the IGCT No. 3 fuse from the engine room relay block No. 2.
Text in Illustration
(f) Remove the AM2 fuse from the engine room junction block assembly.
Text in Illustration
(g) Remove the ECU IG2 fuse from the instrument panel J/B assembly.
Text in Illustration
(h) Disconnect the all connectors from the power management control ECU.
(i) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
(j) Install the IGCT No. 3 fuse, AM2 fuse and ECU IG2 fuse.
(k) Connect the 4 connectors to the power management control ECU Installation.
(l) Install the battery smart unit Installation.
NG -- REPAIR OR REPLACE HARNESS OR CONNECTOR
OK -- Continue to next step.
3. CHECK POWER MANAGEMENT CONTROL ECU
CAUTION:
Be sure to wear insulated gloves and protective goggles.
(a) Check that the service plug grip is not installed.
NOTICE:
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
(b) Remove the battery smart unit Removal.
HINT
Disconnect only the z30 connector of the battery smart unit.
(c) Turn the power switch on (IG).
NOTICE:
* After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
* If the power switch is turned on (IG) with the service plug grip removed, DTCs will be stored. If these DTCs are output, clear the DTCs using the Techstream Hybrid Battery System.
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Text in Illustration
(e) Turn the power switch off.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Text in Illustration
HINT
Resistance becomes 2.0 kOhms or less when there is short circuit in the power management control ECU.
(g) Install the battery smart unit Installation.
NG -- REPLACE POWER MANAGEMENT CONTROL ECU Components
OK -- REPLACE BATTERY SMART UNIT Components