Operation CHARM: Car repair manuals for everyone.

Removal





REAR SUSPENSION: REAR SUSPENSION MEMBER: REMOVAL

1. REMOVE REAR WHEELS

2. REMOVE NO. 2 DIFFERENTIAL SUPPORT PROTECTOR Removal

3. REMOVE NO. 1 DIFFERENTIAL SUPPORT PROTECTOR

HINT
Perform the same procedure as the No. 2 differential support protector.

4. REMOVE REAR SUSPENSION MEMBER BRACE LH Removal

5. REMOVE REAR SUSPENSION MEMBER BRACE RH

HINT
Perform the same procedure as the LH side.

6. REMOVE NO. 2 FLOOR UNDER COVER Removal

7. REMOVE NO. 1 FLOOR UNDER COVER Removal

8. REMOVE REAR NO. 1 FLOOR PANEL BRACE Removal

9. REMOVE FRONT CENTER FLOOR BRACE Removal

10. REMOVE TAIL EXHAUST PIPE ASSEMBLY Removal

11. DISCONNECT HEATED OXYGEN SENSOR Removal

12. REMOVE FRONT EXHAUST PIPE ASSEMBLY Removal

13. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR Removal

14. REMOVE OUTSIDE AIR GUIDE PLATE RH Removal

15. REMOVE PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY Removal

16. DRAIN DIFFERENTIAL OIL Replacement

17. REMOVE REAR AXLE SHAFT NUT LH Removal

18. REMOVE REAR AXLE SHAFT NUT RH

HINT
Perform the same procedure as the LH side.

19. SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY LH Disassembly

20. SEPARATE REAR DISC BRAKE CYLINDER ASSEMBLY RH

HINT
Perform the same procedure as the LH side.

21. REMOVE REAR DISC (for LH Side) Removal

22. REMOVE REAR DISC (for RH Side)

HINT
Perform the same procedure as the LH side.

23. SEPARATE REAR SPEED SENSOR LH Removal

24. SEPARATE REAR SPEED SENSOR RH

HINT
Perform the same procedure as the LH side.

25. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY Removal

26. SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY

HINT
Perform the same procedure as the No. 3 parking brake cable assembly.

27. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY LH Removal

28. REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

HINT
Perform the same procedure as the LH side.

29. REMOVE TOE CONTROL LINK SUB-ASSEMBLY LH Removal

30. REMOVE TOE CONTROL LINK SUB-ASSEMBLY RH

HINT
Perform the same procedure as the LH side.

31. REMOVE REAR NO. 2 UPPER CONTROL ARM ASSEMBLY (for LH Side) Removal

32. REMOVE REAR NO. 2 UPPER CONTROL ARM ASSEMBLY (for RH Side)

HINT
Perform the same procedure as the LH side.

33. REMOVE REAR NO. 1 UPPER CONTROL ARM ASSEMBLY (for LH Side) Removal

34. REMOVE REAR NO. 1 UPPER CONTROL ARM ASSEMBLY (for RH Side)

HINT
Perform the same procedure as the LH side.

35. SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH Removal

36. SEPARATE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT
Perform the same procedure as the LH side.

37. REMOVE REAR AXLE ASSEMBLY LH Removal

38. REMOVE REAR AXLE ASSEMBLY RH

HINT
Perform the same procedure as the LH side.

39. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

(a) Remove the bolt and nut (B), and separate the rear stabilizer link assembly and the height control sensor link bracket.





(b) Remove the bolt (A) and nut, and separate the rear shock absorber with coil spring.

NOTICE:
Turn the bolt while holding the nut.

(c) Remove the bolt and nut (C), and remove the rear No. 2 suspension arm assembly.

40. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

HINT
Perform the same procedure as the LH side.

41. REMOVE REAR DRIVE SHAFT ASSEMBLY LH Removal

42. REMOVE REAR DRIVE SHAFT ASSEMBLY RH

HINT
Perform the same procedure as the LH side.

43. REMOVE HOLE SNAP RING (for LH Side) Removal

44. REMOVE HOLE SNAP RING (for RH Side)

HINT
Perform the same procedure as the LH side.

45. REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY

(a) Disengage the clamp and disconnect the connector.





(b) Remove the 2 bolts and rear height control sensor sub-assembly.





46. REMOVE REAR STABILIZER BAR Removal

47. REMOVE REAR SUSPENSION REAR LOWER MEMBER BRACE LH

(a) Remove the 4 bolts and rear suspension member brace LH.





48. REMOVE REAR SUSPENSION REAR LOWER MEMBER BRACE RH

HINT
Perform the same procedure as the LH side.

49. REMOVE REAR DIFFERENTIAL CARRIER ASSEMBLY Removal

50. REMOVE REAR SUSPENSION MEMBER

(a) Support the rear suspension member with a jack.





(b) Remove the 8 bolts, 2 rear suspension member stoppers, 2 differential support member lower stoppers and rear suspension member lower stoppers from the rear suspension member.





(c) Lower the jack slowly and remove the rear suspension member.

51. REMOVE REAR SUSPENSION MEMBER REAR UPPER STOPPER (for LH Side)

(a) Remove the rear suspension member rear upper stopper from the rear suspension member sub-assembly.





52. REMOVE REAR SUSPENSION MEMBER REAR UPPER STOPPER (for RH Side)

HINT
Perform the same procedure as the LH side.

53. REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for LH Side)

(a) Using SST, remove the rear suspension member front body mounting cushion, while applying grease to the clearance between the rear suspension member front body mounting cushion and the rear suspension member sub-assembly.





SST : 09950-00020

SST : 09950-00030

SST : 09950-40011

09957-04010

SST : 09950-60010

09951-00300

NOTICE:
* Apply a small amount of grease to the threads of SST (center bolt) before use.
* Be careful as the body mounting cushion may fly out.
* The rear suspension member front body mounting cushion cannot be reused.

(b) If the outer casing of the rear suspension member front body mounting cushion remains, insert SST between the rear suspension member front body mounting cushion and the rear suspension member sub-assembly, then remove the outer casing.





SST : 09608-06041

SST : 09950-00020

SST : 09950-00030

SST : 09950-60010

09951-00550

54. REMOVE REAR SUSPENSION MEMBER FRONT BODY MOUNTING CUSHION (for RH Side)

HINT
Perform the same procedure as the LH side.

55. REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION (for LH Side)

(a) Using SST, remove the rear suspension member rear body mounting cushion, while applying grease to the clearance between the rear suspension member rear body mounting cushion and the rear suspension member sub-assembly





SST : 09950-40011

09951-04020

09952-04010

09953-04030

09954-04020

09955-04061

09957-04010

09958-04011

SST : 09950-60010

09951-00320

NOTICE:
* Apply a small amount of grease to the threads of SST (center bolt) before use.
* Be careful as the body mounting cushion may fly out.
* The rear suspension member rear body mounting cushion cannot be reused.

56. REMOVE REAR SUSPENSION MEMBER REAR BODY MOUNTING CUSHION (for RH Side)

HINT
Perform the same procedure as the LH side.

57. REMOVE REAR NO. 1 DIFFERENTIAL MOUNT CUSHION Removal

58. REMOVE REAR NO. 2 DIFFERENTIAL MOUNT CUSHION Removal

59. REMOVE HOLE PLUG

(a) Remove the 4 hole plugs from the rear suspension member sub-assembly.