Installation
A750F AUTOMATIC TRANSMISSION: AUTOMATIC TRANSMISSION ASSEMBLY: INSTALLATION
1. INSTALL TRANSFER ASSEMBLY Installation
2. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY A750F Automatic Transmission
3. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY
(a) Install the torque converter clutch onto the automatic transmission.
(b) Using calipers and a straight edge, measure dimension A, between the engine and the end surface of the drive plate, shown in the illustration.
(c) Using calipers and a straight edge, measure dimension B shown in the illustration and check that B is greater than A measured in (b).
Standard:
A+1 mm or more
4. INSTALL AUTOMATIC TRANSMISSION WITH TRANSFER
(a) Install the automatic transmission onto the engine with the 9 bolts.
Torque : 71 Nm (720 kgf-cm, 53 ft-lbf) for bolt A
Torque : 37 Nm (380 kgf-cm, 27 ft-lbf) for bolt B
(b) Install the 6 torque converter clutch mounting bolts.
Torque : 48 Nm (489 kgf-cm, 35 ft-lbf)
HINT
First install the black bolt and then the other 5 bolts.
5. INSTALL FLYWHEEL HOUSING SIDE COVER
(a) Install the flywheel housing side cover onto the cylinder block.
6. INSTALL STARTER ASSEMBLY Installation
7. INSTALL REAR NO.1 ENGINE MOUNTING INSULATOR
(a) Install the engine mounting insulator rear and 4 bolts onto the automatic transmission.
Torque : 65 Nm (663 kgf-cm, 48 ft-lbf)
8. INSTALL NO.3 FRAME CROSSMEMBER SUB-ASSEMBLY
(a) Install the frame crossmember sub-assembly No. 3 with the 4 bolts and 4 nuts.
Torque : 40 Nm (408 kgf-cm, 30 ft-lbf)
(b) Install the frame crossmember sub-assembly No. 3 with the 4 bolts.
Torque : 19 Nm (189 kgf-cm, 14 ft-lbf)
9. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY
(a) Install the transmission control cable bracket No. 1 with the 2 bolts.
Torque : 28 Nm (286 kgf-cm, 21 ft-lbf)
(b) Connect the transmission control cable with the nut.
Torque : 14 Nm (143 kgf-cm, 10 ft-lbf)
10. INSTALL NO.1 OIL COOLER OUTLET TUBE
(a) Provisionally install the oil cooler outlet tube No. 1.
(b) Provisionally install the oil cooler inlet tube No. 1.
(c) Install the 2 clamps and 2 bolts.
Torque : 12 Nm (122 kgf-cm, 9 ft-lbf) for bolt A
Torque : 5.0 Nm (50 kgf-cm, 43 in-lbf) for bolt B
(d) Using a union nut wrench, tighten the oil cooler outlet tube No. 1.
Torque : 34 Nm (350 kgf-cm, 25 ft-lbf)
11. INSTALL NO.1 OIL COOLER INLET TUBE
(a) Using a union nut wrench, tighten the oil cooler inlet tube No. 1.
Torque : 34 Nm (350 kgf-cm, 25 ft-lbf)
12. INSTALL NO.2 MANIFOLD STAY
(a) Install manifold stay No. 2 with the 3 bolts.
Torque : 40 Nm (408 kgf-cm, 30 ft-lbf)
13. INSTALL MANIFOLD STAY
(a) Install the manifold stay with the 3 bolts.
Torque : 40 Nm (408 kgf-cm, 30 ft-lbf)
14. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
15. INSTALL FRONT PROPELLER SHAFT ASSEMBLY Installation
16. INSTALL EXHAUST PIPE
Installation
17. CONNECT OXYGEN SENSOR
18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque : 3.9 Nm (40 kgf-cm, 35 in-lbf)
19. PERFORM INITIALIZATION
A750F Automatic Transmission System
20. ADD AUTOMATIC TRANSMISSION FLUID
A750F Automatic Transmission
21. INSPECT SHIFT LEVER POSITION A750F Automatic Transmission
22. CHECK FOR EXHAUST GAS LEAKAGE
23. INSTALL NO. 2 ENGINE UNDER COVER (w/ No. 2 Engine Under Cover)
24. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY