Removal and Installation

HEADLINING

Removal and Installation


REMOVAL






1.Remove sun visor cap (1) using a remover tool (A), and then remove sunvisor assembly fixing TORX screws.
2.Disconnect vanity mirror lamp harness connector, and then remove sun visor assembly (LH and RH).





3.Rotate sun visor holder (1) (LH and RH) at approximately 90
degrees, and then pull it out to remove.





4.Insert a remover tool (A) into the gap between lane camera finisher (1), and then remove lane camera finisher (if equipped).





5.Remove light & rain sensor cover / rain sensor cover. Refer to "Removal and Installation" Removal and Installation.





6.Disconnect harness connectors.
- Lane camera unit harness connector (1) (if equipped).
- Inside mirror harness connector (2).
- Light & rain sensor harness connector / rain sensor harness connector (3).
7.Remove assist grips





- Insert a small flat-bladed screwdriver (A) into the gap between assist grip cap (1), and then remove assist grip cap.
- Remove assist grip mounting bolts, and then remove assist grips (2).





8.Insert a remover tool (A) between luggage room lamp (1) and roof garnish to disengage the fixing metal clips, and then disconnect luggage room lamp harness connector.

CAUTION:
Apply protective tape (B) to the roof garnish to protect from damage.










9.Insert a remover tool (A) between roof garnish (1) and body panel to disengage the fixing clips and pawls, and then remove roof garnish.





10.Remove front pillar garnish (LH and RH). Refer to "FRONT PILLAR GARNISH : Removal and Installation" Front Pillar Garnish.
11.Remove front kicking plate inner (LH and RH) and rear kicking plate inner (LH and RH). Refer to "KICKING PLATE INNER : Removal and Installation" Kicking Plate Inner.
12.Remove dash side finisher (LH and RH). Refer to "DASH SIDE FINISHER : Removal and Installation" Dash Side Finisher.
13.Remove center pillar lower garnish (LH and RH). Refer to "CENTER PILLAR LOWER GARNISH : Removal and Installation" Center Pillar Lower Garnish.
14.Remove luggage side lower finisher (LH and RH). Refer to "LUGGAGE SIDE LOWER FINISHER : Removal and Installation" Luggage Side Lower Finisher.
15.Remove front body side welt (LH and RH) and rear body side welt (LH and RH). Refer to "BODY SIDE WELT : Removal and Installation" Body Side Welt.
16.Remove center pillar upper garnish (LH and RH). Refer to "CENTER PILLAR UPPER GARNISH : Removal and Installation" Center Pillar Upper Garnish.
17.Remove rear pillar finisher (LH and RH). Refer to "REAR PILLAR FINISHER : Removal and Installation" Rear Pillar Finisher.
18.Remove back pillar garnish (LH and RH). Refer to "BACK PILLAR GARNISH : Removal and Installation" Back Pillar Garnish.
19.Remove luggage side upper finisher (LH and RH). Refer to "LUGGAGE SIDE UPPER FINISHER : Removal and Installation" Luggage Side Upper Finisher.





20.Insert a remover tool between map lamp assembly (1) and headlining assembly to disengage the fixing metal clips, and then remove map lamp assembly.





21.Peel off dual lock fastener between headlining assembly and roof panel.
22.Remove headlining clips located at the rear side
23.Remove headlining assembly (1) through the back door.






CAUTION:
- When removing, 2 workers are required.
- Never bend headlining when removing.
- Be careful not to scratch or damage any part of the body while taking out the headlining.
24.Remove the following parts after removing headlining assembly.
- Personal lamp assembly. Refer to "Removal and Installation" Removal and Installation.
- Rear ventilator grille assembly. Refer to "REAR VENTILATOR GRILLE : Removal and Installation" Rear Ventilator Grille.
- Headlining harness.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:
- Be careful not to bend headlining when installing.
- First install metal clips of map lamp assembly and clips of the rear end of headlining for positioning.