Operation CHARM: Car repair manuals for everyone.

Installation





INTERIOR PANELS / TRIM: ROOF HEADLINING: INSTALLATION

1. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Install the front door opening trim weatherstrip LH as shown in the illustration.





2. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

(a) Install the front door opening trim weatherstrip RH as shown in the illustration.





3. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH

(a) Install the rear door opening trim weatherstrip LH as shown in the illustration.





4. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH

(a) Install the rear door opening trim weatherstrip RH as shown in the illustration.





5. INSTALL NO. 1 ROOF WIRE (w/o Sliding Roof)

(a) Install the roof wire.

(1) Remove the peeling paper from one side of double-sided tape.

(2) Attach double-sided tape to the marks on the roof headlining as shown in the illustration.

(3) Remove the peeling paper from the other side of double-sided tape.

(4) Align the wire harness to double-sided tape. Also, align the marking tape areas of the wire harness to the marks on the roof headlining. Temporarily attach the wire harness to the roof headlining. Secure the wire harness to the roof headlining with vinyl tape.





NOTICE:
Securely install the No. 1 roof wire. If the wire is not secured, noise will occur.

6. INSTALL NO. 1 ROOF WIRE (w/ Sliding Roof)

(a) Install the roof wire.

(1) Remove the peeling paper from one side of double-sided tape.

(2) Attach double-sided tape to the marks on the roof headlining as shown in the illustration.

(3) Remove the peeling paper from the other side of double-sided tape.

(4) Align the wire harness to double-sided tape. Also, align the marking tape areas of the wire harness to the marks on the roof headlining. Temporarily attach the wire harness to the roof headlining. Secure the wire harness to the roof headlining with vinyl tape.





NOTICE:
Securely install the No. 1 roof wire. If the wire is not secured, noise will occur.

7. INSTALL VANITY LIGHT ASSEMBLY

(a) Engage the claw [A], and then install the bulb holder with the 2 claws [B] to install the vanity light assembly.





HINT
Use the same procedure to install the light on the other side.

8. INSTALL NO. 2 ROOF HEADLINING PAD

(a) Install the 2 No. 2 roof headlining pads using double-sided tape.





9. INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the rear No. 2 side rail spacer LH and install the spacer using double-sided tape as shown in the illustration.





10. INSTALL REAR NO. 2 SIDE RAIL SPACER RH (w/o Sliding Roof)

HINT
Use the same procedure for the RH side and the LH side.

11. INSTALL REAR ROOF SILENCER PAD (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the roof silencer pads and install the pads using double-sided tape as shown in the illustration.





12. INSTALL ROOF HEADLINING PAD LH (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the roof headlining pad LH and install the pads using double-sided tape as shown in the illustration.





13. INSTALL CENTER ROOF SILENCER PAD (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the center roof silencer pad and install the pad using double-sided tape as shown in the illustration.





14. INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)

(a) Align the markings on the roof headlining assembly with the No. 1 roof silencer pad and install the pad using double-sided tape as shown in the illustration.





15. INSTALL REAR SIDE RAIL SPACER LH (w/ Sliding Roof)

(a) Align the markings on the roof headlining assembly with the rear side rail spacer LH and install the spacer using double-sided tape as shown in the illustration.





16. INSTALL REAR SIDE RAIL SPACER RH (w/ Sliding Roof)

HINT
Use the same procedure for the RH side and the LH side.

17. INSTALL ROOF HEADLINING PAD

(a) Align the markings on the roof headlining assembly with the roof headlining pads and install the pads using double-sided tape as shown in the illustration.





18. INSTALL ROOF HEADLINING ASSEMBLY (w/o Sliding Roof)

(a) Place the roof headlining in the vehicle from the front right door.





(b) Engage the hook, 10 claws and 2 clips, and install the roof headlining assembly.





(c) Connect the roof wire connector and engage each clamp.





(d) Connect each connector to the map light assembly.

19. INSTALL ROOF HEADLINING ASSEMBLY (w/ Sliding Roof)

(a) Place the roof headlining in the vehicle from the front right door.





(b) Engage the hook, 10 claws, 8 fasteners and 2 clips, and install the roof headlining assembly.





(c) Connect the roof wire connector and engage each clamp.





(d) Connect each connector to the map light assembly.

20. INSTALL VISOR HOLDER

(a) Set the claws of the visor holder as shown in the illustration





(b) Engage the claws and install the visor holder.

HINT
Use the same procedure to install the holder on the other side.

21. INSTALL VISOR ASSEMBLY LH

(a) Install the visor assembly LH with the 2 screws.





22. INSTALL VISOR ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

23. INSTALL VISOR BRACKET COVER

(a) Engage the 4 claws and install the visor bracket cover.





HINT
Use the same procedure to install the cover on the other side.

24. INSTALL ASSIST GRIP SUB-ASSEMBLY

(a) Put an assist grip sub-assembly together as shown in the illustration.





(b) Install the assist grip sub-assembly.

HINT
Use the same procedure for the other 3 assist grips.

25. INSTALL COAT HOOK

(a) Install the coat hook with the screw.





HINT
Use the same procedure to install the hook on the other side.

26. INSTALL SPOT LIGHT ASSEMBLY Installation

27. INSTALL MAP LIGHT ASSEMBLY (w/o Sliding Roof) Service and Repair

28. INSTALL MAP LIGHT ASSEMBLY (w/ Sliding Roof) Service and Repair

29. INSTALL RAIN SENSOR TAPE Installation

30. INSTALL RAIN SENSOR Installation

31. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER Installation

32. INSTALL ROOF SIDE INNER GARNISH LH

(a) Engage the claw and 4 clips, and install the roof side garnish inner LH.





33. INSTALL ROOF SIDE INNER GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

34. INSTALL REAR SEAT SIDE GARNISH LH

(a) Engage the 5 claws and install the rear seat side garnish LH.





35. INSTALL REAR SEAT SIDE GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

36. INSTALL CENTER PILLAR GARNISH LH

(a) Engage the 2 claws and install the center pillar garnish LH.





(b) Install the 2 screws.

37. INSTALL LOWER CENTER PILLAR GARNISH LH

(a) Engage the 5 clips and 3 claws, and install the lower center pillar garnish LH.





38. INSTALL FRONT SEAT OUTER BELT ASSEMBLY LH

(a) Install the front seat outer belt assembly LH with the bolt.





Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)

39. INSTALL LAP BELT OUTER ANCHOR COVER LH

(a) Engage the 2 claws and install the lap belt outer anchor cover as shown in the illustration.





40. INSTALL CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

41. INSTALL FRONT SEAT OUTER BELT ASSEMBLY RH

(a) Install the front seat outer belt assembly RH with the bolt.





Torque : 42 Nm (428 kgf-cm, 31 ft-lbf)

(b) Connect the connector.

42. INSTALL LOWER CENTER PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

43. INSTALL FRONT SEAT BELT ANCHOR COVER SUB-ASSEMBLY

(a) Engage the 3 claws and install the front seat belt anchor cover sub-assembly.





44. INSTALL REAR DOOR SCUFF PLATE LH

(a) Engage the 2 clips.





(b) Engage the 5 claws and install the rear door scuff plate LH.





45. INSTALL REAR DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

46. INSTALL TRANSMISSION FLOOR SHIFT ASSEMBLY Installation

47. CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY Installation

48. ADJUST SHIFT LEVER POSITION Adjustments

49. INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR Installation

50. INSTALL FRONT EXHAUST PIPE ASSEMBLY Installation

51. CONNECT HEATED OXYGEN SENSOR Installation

52. INSTALL FRONT CENTER FLOOR BRACE Installation

53. INSTALL REAR NO. 1 FLOOR PANEL BRACE Installation

54. INSTALL TAIL EXHAUST PIPE ASSEMBLY Installation

55. INSTALL NO. 2 FLOOR UNDER COVER Installation

56. INSTALL NO. 1 FLOOR UNDER COVER Installation

57. INSTALL INSTRUMENT PANEL STAY Installation

58. INSTALL INSTRUMENT PANEL CLIP Installation

59. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY Installation

60. CONNECT NO. 2 INSTRUMENT PANEL WIRE Installation

61. INSTALL NO. 1 CONSOLE BOX DUCT Installation

62. INSTALL NO. 2 CONSOLE BOX DUCT Installation

63. INSTALL FRONT STEREO COMPONENT SPEAKER ASSEMBLY (w/ Front Center Speaker) Installation

64. INSTALL NO. 3 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY Installation

65. INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY Installation

66. INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY Installation

67. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY Installation

68. INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY Installation

69. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Installation

70. INSTALL SIDE INSTRUMENT PANEL RH Installation

71. INSTALL COMBINATION METER ASSEMBLY Installation

72. INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY Installation

73. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY Installation

74. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY Installation

75. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY Installation

76. INSTALL SIDE INSTRUMENT PANEL LH Installation

77. INSTALL FRONT PILLAR GARNISH LH

(a) Remove the protective cover.

(b) Make sure that the front pillar garnish clip is not damaged.





NOTICE:
* If there is any damage, replace the garnish clip with a new one.
* When a garnish clip is being replaced, make sure to install it in the direction shown in the illustration.

(c) Engage the guide.

(d) Turn the end of the front pillar garnish clip 90° with needle-nosed pliers and install it to the front pillar garnish LH.

HINT
Tape the tips of the needle-nosed pliers before use.

(e) Engage the 2 clips to install the front pillar garnish LH.





78. INSTALL FRONT PILLAR GARNISH RH

HINT
Use the same procedure for the RH side and the LH side.

79. INSTALL FRONT DOOR OPENING TRIM COVER LH

(a) Engage the 4 claws and install the front door opening trim cover LH.





80. INSTALL FRONT DOOR OPENING TRIM COVER RH

HINT
Use the same procedure for the RH side and the LH side.

81. INSTALL FRONT DOOR SCUFF PLATE LH

(a) Engage the 4 clips.





(b) Engage the 7 claws and install the front door scuff plate LH.





82. INSTALL FRONT DOOR SCUFF PLATE RH

HINT
Use the same procedure for the RH side and the LH side.

83. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY Installation

84. INSTALL STEERING COLUMN COVER Installation

85. ADJUST SPIRAL CABLE Installation

86. INSTALL STEERING WHEEL ASSEMBLY Installation

87. INSTALL STEERING PAD Installation

88. INSTALL LOWER NO. 3 STEERING WHEEL COVER Installation

89. INSTALL LOWER NO. 2 STEERING WHEEL COVER Installation

90. INSTALL INTEGRATION CONTROL PANEL WITH RADIO RECEIVER ASSEMBLY (w/o Multi-display) Installation

91. INSTALL DISPLAY AND NAVIGATION MODULE DISPLAY WITH RADIO RECEIVER ASSEMBLY (w/ Multi-display) Installation

92. INSTALL CENTER LOWER INSTRUMENT CLUSTER FINISH PANEL Installation

93. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY Installation

94. INSTALL CONSOLE BOX Installation

95. INSTALL CONSOLE BOX REGISTER ASSEMBLY (w/ Ashtray) Installation

96. INSTALL CONSOLE BOX REGISTER ASSEMBLY (w/o Ashtray) Installation

97. INSTALL REAR ASH RECEPTACLE ASSEMBLY (w/ Ashtray) Installation

98. INSTALL FRONT ASH RECEPTACLE BOX SUB-ASSEMBLY (w/ Ashtray) Installation

99. INSTALL INSTRUMENT PANEL BOX ASSEMBLY (w/o Ashtray) Installation

100. INSTALL CONSOLE PANEL SUB-ASSEMBLY Installation

101. INSTALL UPPER NO. 2 CONSOLE PANEL GARNISH Installation

102. INSTALL UPPER NO. 1 CONSOLE PANEL GARNISH Installation

103. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY Installation

104. INSTALL FRONT SEAT ASSEMBLY LH Installation

105. INSTALL REAR INNER SEAT TRACK BRACKET COVER LH Installation

106. INSTALL REAR OUTER SEAT TRACK BRACKET COVER LH Installation

107. INSTALL FRONT INNER SEAT TRACK BRACKET COVER LH Installation

108. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER LH Installation

109. INSTALL FRONT SEAT ASSEMBLY RH

HINT
Use the same procedure for the RH side and the LH side.

110. INSTALL REAR INNER SEAT TRACK BRACKET COVER RH

HINT
Use the same procedure for the RH side and the LH side.

111. INSTALL REAR OUTER SEAT TRACK BRACKET COVER RH

HINT
Use the same procedure for the RH side and the LH side.

112. INSTALL FRONT INNER SEAT TRACK BRACKET COVER RH

HINT
Use the same procedure for the RH side and the LH side.

113. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER RH

HINT
Use the same procedure for the RH side and the LH side.

114. INSTALL FRONT SEAT HEADREST ASSEMBLY

115. INSTALL REAR SEATBACK ASSEMBLY Installation

116. INSTALL REAR SEAT HEADREST ASSEMBLY LH

117. INSTALL REAR SEAT HEADREST ASSEMBLY RH

118. INSTALL REAR SEAT CUSHION ASSEMBLY Installation

119. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
Some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.

120. INSPECT STEERING PAD Installation

121. INSPECT SRS WARNING LIGHT

Diagnosis System.

122. INSPECT FRONT SEAT ASSEMBLY Installation

123. INSPECT SHIFT LEVER POSITION Initial Inspection and Diagnostic Overview

124. INSPECT FOR EXHAUST GAS LEAK

If exhaust gas is leaking, tighten the related parts to stop the leak. Replace damaged parts as necessary.