Removal
2UR-FSE INTAKE: INTAKE MANIFOLD: REMOVAL
NOTICE:
While the battery is connected, even if the power switch is OFF, the brake control system activates when the brake pedal is depressed or the door courtesy switch turns on. Therefore during servicing of the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.
1. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY Removal
2. REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire) Removal
3. REMOVE BATTERY SERVICE HOLE COVER LH Removal
4. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.
NOTICE:
* w/ Navigation System (for HDD):
After the power switch is turned off, the display and navigation module display (HDD navigation system) records various types of memory and settings. As a result, after turning the power switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal:
* When disconnecting the cable, some systems need to be initialized after the cable is reconnected Repair Instruction - Initialization.
5. REMOVE SERVICE PLUG GRIP
(a) Remove the service plug grip Removal.
6. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH Removal
7. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH Removal
8. REMOVE NO. 1 ENGINE UNDER COVER Removal
9. DRAIN ENGINE COOLANT Service and Repair
10. REMOVE V-BANK COVER SUB-ASSEMBLY Removal
11. REMOVE AIR CLEANER INLET COVER SUB-ASSEMBLY Removal
12. REMOVE ENGINE ROOM SIDE COVER RH Removal
13. REMOVE ENGINE ROOM SIDE COVER LH Removal
14. REMOVE NO. 1 AIR CLEANER INLET Removal
15. REMOVE INTAKE AIR CONNECTOR PIPE Removal
16. REMOVE AIR CLEANER ASSEMBLY LH Removal
17. REMOVE AIR CLEANER ASSEMBLY RH Removal
18. DISCONNECT NO. 1 MOTOR COOLING PIPE Removal
19. REMOVE SKID CONTROL ECU Removal
20. DISCONNECT NO. 3 RELAY BLOCK Removal
21. DISCONNECT BRAKE FLUID RESERVOIR Removal
22. REMOVE SKID CONTROL ECU BRACKET Removal
23. REMOVE ENGINE COVER SUB-ASSEMBLY LH Removal
24. REMOVE NO. 6 COVER SUB-ASSEMBLY Removal
25. REMOVE ENGINE ROOM ECU COVER Removal
26. REMOVE OUTLET ENGINE ROOM ECM DUCT Removal
27. DISCONNECT HYBRID VEHICLE CONTROL ECU CONNECTOR
(a) Disconnect the connector from the hybrid vehicle control ECU.
28. REMOVE NO. 2 CONNECTOR HOLDER
(a) Disconnect the 3 connectors.
(b) Detach the wire harness's clamp A from the ECM box.
(c) Detach the 2 claws and remove the No. 2 connector holder.
29. DISCONNECT ECM CONNECTOR
(a) Disconnect the 4 ECM connectors and remove the engine wire harness from the ECM box.
30. DISCONNECT ENGINE WIRE HARNESS
(a) Disconnect the engine wire harness connectors.
HINT
To disconnect the 4 injector driver connectors, (1) push the claw downward and (2) move the lock lever to release the lock.
(b) Using a clip remover, detach the 4 engine wire harness clamps labeled A.
(c) Disconnect the 3 engine wire harness clamps labeled B.
(d) Remove the 4 bolts and disconnect the 4 ground cables.
(e) Remove the 3 bolts and disconnect the 3 wire harness brackets.
(f) Remove the 4 nuts and disconnect the engine wire harness protector from the intake manifold.
31. REMOVE INJECTOR DRIVER
(a) Disconnect the 4 injector driver connectors as follows: (1) push the claw downward, and (2) move the lock lever to release the lock.
(b) Using a clip remover, detach the 3 wire harness clamps.
(c) Remove the 2 bolts, 2 nuts and injector driver.
(d) Remove the No. 1 engine cover.
32. REMOVE FLEXIBLE HOSE BRACKET SUB-ASSEMBLY
(a) Disconnect the flexible hose.
(b) Remove the bolt and flexible hose bracket.
33. REMOVE ENGINE MOTOR CABLE CLAMP BRACKET
(a) Using a clip remover, detach the wire harness clamp.
(b) Remove the bolt and engine motor cable clamp bracket.
34. REMOVE NO. 3 ENGINE COVER SUB-ASSEMBLY Removal
35. REMOVE THROTTLE BODY ASSEMBLY Removal
36. REMOVE WATER BY-PASS PIPE HOSE
(a) Disconnect the 4 water hoses and remove the 2 bolts and water by-pass pipe hose.
37. REMOVE PURGE VSV
(a) Disconnect the VSV connector.
(b) Disconnect the 2 purge line hoses.
(c) Remove the bolt and VSV.
38. DISCONNECT PCV HOSE
(a) Disconnect the PCV hose from the intake manifold.
39. REMOVE INTAKE MANIFOLD
(a) Remove the 8 bolts, 2 nuts and intake manifold.
(b) Remove the 2 gaskets.