Removal
A750F AUTOMATIC TRANSMISSION / TRANSAXLE: AUTOMATIC TRANSMISSION ASSEMBLY: REMOVAL
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Removal.
2. REMOVE CONSOLE BOX ASSEMBLY (for VF2A)
(a) Remove the console box assembly Removal.
3. REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY (for VF2A)
(a) Remove the 4screws and No. 1 shift and select lever boot.
(b) Fold back the transfer front drive shift boot.
(c) Using needle-nose pliers, remove the snap ring and pull out the transfer high and low shift lever.
4. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY Removal
5. REMOVE REAR ENGINE UNDER COVER ASSEMBLY Removal
6. REMOVE FRONT FENDER APRON SEAL RH Removal
7. REMOVE NO. 1 FRONT FENDER APRON TO FRAME SEAL RH Removal
8. DRAIN AUTOMATIC TRANSMISSION FLUID Removal
9. REMOVE TRANSFER CASE LOWER PROTECTOR
(a) Remove the 4 bolts and transfer case lower protector.
10. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
(a) Remove the front propeller shaft Removal.
11. REMOVE PROPELLER SHAFT ASSEMBLY
(a) Remove the propeller shaft Removal.
12. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(a) Remove the front exhaust pipe assembly Removal.
13. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
(a) Remove the nut and clip, and disconnect the transmission control cable from the automatic transmission.
14. DISCONNECT NO. 1 INLET OIL COOLER TUBE AND NO. 1 OUTLET OIL COOLER TUBE
(a) Remove the 2 bolts to open the 2 No. 2 flexible hose clamps.
(b) Using a union nut wrench, disconnect the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube from each oil cooler tube union.
15. REMOVE MANIFOLD STAY
(a) Remove the 3 bolts and stay.
16. REMOVE NO. 2 MANIFOLD STAY
(a) Remove the 3 bolts and stay.
17. REMOVE STARTER ASSEMBLY
(a) Remove the starter assembly Removal.
18. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT
(a) Remove the flywheel housing side cover.
(b) Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley setting bolt with a wrench.
19. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY
(a) Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.
20. REMOVE FRONT SUSPENSION MEMBER BRACKET LH AND RH (for X-Runner)
(a) Remove the 8 bolts and front suspension member bracket LH and RH.
21. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
(a) Remove the 4 bolts of the rear engine mounting insulator.
(b) Remove the 4 nuts, 4 bolts and frame crossmember.
22. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
(a) Remove the bolt and rear engine mounting heat insulator.
(b) Remove the 4 bolts and rear engine mounting insulator from the transmission.
23. DISCONNECT WIRE HARNESS AND CONNECTOR
(a) Remove the nut and disconnect the ground cable.
(b) Tilt the transmission downward.
NOTICE:
Make sure the cooling fan does not contact the fan shroud.
(c) for VF4BM:
(1) Disconnect the park/neutral position switch connector, transmission wire connector, 2 transmission speed sensor connectors and transfer control side connectors.
HINT
Detach the claw, press down the lever, and then disconnect the transmission wire connector.
(2) Detach the 2 connector clamps and 7 harness clamps, and disconnect wire harness.
(d) for VF2A:
(1) Disconnect the park/neutral position switch connector, transmission wire connector, 2 transmission speed sensor connectors and 3 transfer connectors.
HINT
Detach the claw, press down the lever, and then disconnect the transmission wire connector.
(2) Detach the 2 connector clamps and 5 harness clamps, and disconnect the wire harness.
24. DISCONNECT BREATHER PLUG HOSE
(a) Disconnect the 3 breather plug hoses from the engine.
25. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
(a) Remove the 9 bolts and transmission.
NOTICE:
Do not use excess force when prying the transmission assembly.
26. REMOVE TRANSFER ASSEMBLY
(a) for VF4BM:
Remove the transfer Removal.
(b) for VF2A:
Remove the transfer Removal.
27. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET
(a) Remove the 2 bolts and control cable bracket.
28. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY
29. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY
(a) Inspect the torque converter clutch Testing and Inspection.